AudioCodes Mediant 2000

User's Manual 576 Document #: LTRT-68822
Mediant 2000
Parameter Description
[RTPOnlyModeForTrunk
_x]
Enables the RTP Only feature per trunk, where ID denotes the trunk
number (0 is the first trunk). For more information, see the
RTPOnlyMode parameter.
Note: For using the global parameter (i.e., setting the RTP Only feature
for all trunks), set this parameter to -1 (default).
Web/EMS: SIT Q850
Cause
[SITQ850Cause]
Defines the Q.850 cause value specified in the SIP Reason header that
is included in a 4xx response when a Special Information Tone (SIT) is
detected on an IP-to-Tel call.
The valid range is 0 to 127. The default is 34.
Note: For mapping specific SIT tones, you can use the
SITQ850CauseForNC, SITQ850CauseForIC, SITQ850CauseForVC,
and SITQ850CauseForRO parameters.
Web/EMS: SIT Q850
Cause For NC
[SITQ850CauseForNC]
Defines the Q.850 cause value specified in the SIP Reason header that
is included in a 4xx response when SIT-NC (No Circuit Found Special
Information Tone) is detected from the TelPSTN for IP-to-Tel calls.
The valid range is 0 to 127. The default is 34.
Notes:
 When not configured (i.e., default), the SITQ850Cause parameter is
used.
 This parameter is applicable only to FXO interfaces.
Web/EMS: SIT Q850
Cause For IC
[SITQ850CauseForIC]
Defines the Q.850 cause value specified in the SIP Reason header that
is included in a 4xx response when SIT-IC (Operator Intercept Special
Information Tone) is detected from the PSTN for IP-to-Tel calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note:
When not configured (i.e., default), the SITQ850Cause parameter
is used.
Web/EMS: SIT Q850
Cause For VC
[SITQ850CauseForVC]
Defines the Q.850 cause value specified in the SIP Reason header that
is included in a 4xx response when SIT-VC (Vacant Circuit - non-
registered number Special Information Tone) is detected from the PSTN
for IP-to-Tel calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note:
When not configured (i.e., default), the SITQ850Cause parameter
is used.
Web/EMS: SIT Q850
Cause For RO
[SITQ850CauseForRO]
Defines the Q.850 cause value specified in the SIP Reason header that
is included in a 4xx response when SIT-RO (Reorder - System Busy
Special Information Tone) is detected from the PSTN for IP-to-Tel calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note: When not configured (i.e., default), the SITQ850Cause parameter
is used.
[GWInboundManipulatio
nSet]
Selects the Manipulation Set ID for manipulating all inbound INVITE
messages. The Manipulation Set is defined using the
MessageManipulations parameter. By default, no manipulation is done
(i.e. Manipulation Set ID is set to -1).
[GWOutboundManipulat
ionSet]
Selects the Manipulation Set ID for manipulating all outbound INVITE
messages. The Manipulation Set is defined using the
MessageManipulations parameter. By default, no manipulation is done
(i.e. Manipulation Set ID is set to -1).
Note: This parameter is used only if the Outbound Message
Manipulation Set parameter of the destination IP Group is not set.