Name: HP 830 Series
Brand: HP
Rating: 4 (1 reviews)

To Next Page

To Previous Page

Figure 46 Network diagram

Configuration procedure

1. Set the rate of GigabitEthernet 1/0/4 to 1000 Mbps:

a. Select Device > Port Management from the navigation tree.

b. Click the Setup tab.

c. Select 1000 from the Speed list.

d. Select 4 on the chassis front panel. 4 represents port GigabitEthernet 1/0/4.

e. Click Apply.

Default Chapter3
- Table of Contents3
Web Overview13
- Web Interface13
- Web User Level14
- Web-Based NM Functions14
- Common Items on the Web Pages22
Logging in to the Web Interface27
- Restrictions and Guidelines27
- Logging out of the Web Interface32
Configuration Wizard33
- Basic Service Setup33
Accessing the Controller Engine from the Switching Engine38
- Specifying Management IP Addresses at the CLI38
- Accessing the Controller Engine from the Switching Engine's Web Interface39
Displaying Information Summary40
- Displaying System Information40
- Displaying Device Information41
Configuring Basic Device Settings43
- Configuring System Name43
- Configuring Web Idle Timeout Period43
Maintaining Devices44
- Rebooting the Device44
- Displaying the Electronic Label Information45
- Generating the Diagnostic Information File45
Configuring the System Time47
- Configuration Guidelines47
- Displaying the System Time47
  - Configuring Network Time48
- System Time Configuration Example49
Managing Logs51
- Displaying Syslogs51
- Setting the Log Host53
- Setting Buffer Capacity and Refresh Interval54
Managing the Configuration55
- Backing up the Configuration55
- Restoring the Configuration55
- Saving the Configuration56
- Initializing the Configuration57
Managing Files58
- Displaying Files58
- Downloading a File58
- Uploading a File59
- Removing a File59
Managing Ports60
- Setting Operation Parameters for a Port60
- Displaying Port Operation Parameters65
  - Displaying a Specified Operation Parameter for All Ports65
  - Displaying All the Operation Parameters for a Port65
- Port Management Configuration Example66
  - Network Requirements66
  - Configuration Procedure67
Configuring Port Mirroring71
- Terminologies of Port Mirroring71
- Local Port Mirroring Implementation71
- Configuration Guidelines72
- Recommended Configuration Procedures72
- Creating a Mirroring Group73
- Configuring Ports for a Mirroring Group73
- Local Port Mirroring Configuration Example75
Managing Users79
- Creating a User79
- Setting the Super Password80
- Switching to the Management Level81
Configuring a Loopback Test83
Configuring VCT85
Configuring the Flow Interval86
- Setting the Traffic Statistics Generating Interval86
- Displaying Port Traffic Statistics86
Configuring Storm Constrain88
- Setting the Traffic Statistics Generating Interval88
- Configuring Storm Constrain89
Configuring RMON91
- Overview91
- Recommended Configuration Procedure93
- Configuring a Statistics Entry95
- Configuring a History Entry96
- Configuring an Event Entry97
- Configuring an Alarm Entry98
- Displaying RMON Statistics100
- Displaying RMON History Sampling Information102
- Displaying RMON Event Logs103
- RMON Configuration Example104
Configuring Energy Saving108
Configuring SNMP110
- Overview110
  - SNMP Mechanism110
  - SNMP Protocol Versions111
- Recommended Configuration Procedure111
  - Enabling SNMP Agent112
- Configuring an SNMP View114
  - Creating an SNMP View114
  - Adding Rules to an SNMP View115
- Configuring an SNMP Community116
- Configuring an SNMP Group117
- Configuring an SNMP User118
- Configuring SNMP Trap Function120
- Displaying SNMP Packet Statistics121
- Snmpv1/V2C Configuration Example122
- Snmpv3 Configuration Example125
Displaying Interface Statistics130
Configuring Vlans131
- Overview131
- Configuration Guidelines134
- Recommended VLAN Configuration Procedures135
  - Recommended Configuration Procedure (Modifying Ports in a VLAN)135
  - Recommended Configuration Procedure (Modifying the Vlans to Which a Port Belongs)135
- Creating Vlans135
- Selecting Vlans136
- Modifying a VLAN137
- Modifying Ports139
- VLAN Configuration Example140
Configuring VLAN Interfaces145
- Overview145
- Configuration Guidelines145
- Creating a VLAN Interface145
- Modifying a VLAN Interface147
Configuring a Voice VLAN149
- Overview149
- Configuration Guidelines152
- Recommended Voice VLAN Configuration Procedure152
- Configuring Voice VLAN Globally153
- Configuring Voice VLAN on Ports154
- Adding OUI Addresses to the OUI List155
- Voice VLAN Configuration Examples156
  - Configuring Voice VLAN on a Port in Automatic Voice VLAN Assignment Mode156
  - Configuring Voice VLAN on a Port in Manual Voice VLAN Assignment Mode161
Configuring the MAC Address Table168
- Overview168
- Displaying and Configuring MAC Address Entries169
- Setting the Aging Time of MAC Address Entries171
- MAC Address Table Configuration Example172
Configuring MSTP173
- Overview173
- Why MSTP173
  - STP and RSTP Limitations173
  - Features of MSTP173
- Basic Concepts in MSTP174
- How MSTP Works178
  - CIST Calculation178
  - MSTI Calculation178
- MSTP Implementation on Devices178
- Protocols and Standards178
- Configuration Guidelines179
- Recommended MSTP Configuration Procedure179
- Configuring an MST Region179
- Configuring MSTP Globally181
- Configuring MSTP on a Port183
- Displaying MSTP Information for a Port185
- MSTP Configuration Example188
Configuring Link Aggregation and LACP192
- Overview192
- Configuration Guidelines195
- Recommended Link Aggregation and LACP Configuration Procedures196
- Creating a Link Aggregation Group197
- Displaying Information about an Aggregate Interface198
- Setting LACP Priority199
- Displaying Information about LACP-Enabled Ports200
- Link Aggregation and LACP Configuration Example202
Configuring LLDP205
- Overview205
- Compatibility of LLDP with CDP209
- Protocols and Standards210
- Configuration Guidelines210
- Recommended LLDP Configuration Procedure210
- Enabling LLDP on Ports211
- Configuring LLDP Settings on Ports212
  - Setting LLDP Parameters for a Single Port212
  - Configuring LLDP Settings for Ports in Batch215
- Configuring Global LLDP Setup216
- Displaying LLDP Information for a Port218
- Displaying Global LLDP Information222
- Displaying LLDP Information Received from LLDP Neighbors224
- LLDP Configuration Examples224
  - LLDP Basic Settings Configuration Example224
  - CDP-Compatible LLDP Configuration Example231
Configuring ARP238
- Overview238
- Configuring ARP Entries240
  - Displaying ARP Entries240
  - Creating a Static ARP Entry241
- Removing ARP Entries241
- Configuring Gratuitous ARP241
  - Static ARP Configuration Example242
Configuring ARP Attack Defense246
- Overview246
  - User Validity Check246
  - ARP Packet Validity Check246
- Configuring ARP Detection246
Configuring IGMP Snooping248
- Overview248
- Recommended Configuration Procedure251
- Enabling IGMP Snooping Globally252
- Configuring IGMP Snooping in a VLAN252
- Configuring IGMP Snooping Port Functions254
- Displaying IGMP Snooping Multicast Table Entries255
- IGMP Snooping Configuration Example256
Configuring Ipv4 and Ipv6 Routing261
- Overview261
- Configuration Guidelines262
- Displaying the Ipv4 Active Route Table262
- Creating an Ipv4 Static Route263
- Displaying the Ipv6 Active Route Table264
- Creating an Ipv6 Static Route264
- Ipv4 Static Route Configuration Example265
- Ipv6 Static Route Configuration Example269
Configuring Ipv6 Services272
DHCP Overview273
- Dhcp273
- DHCP Snooping273
- Configuring the DHCP Server274
- Recommended Configuration Procedure274
- Enabling DHCP274
- Configuring the DHCP Relay Agent279
- Configuring DHCP Snooping284
- DHCP Server Configuration Examples287
  - Static IP Address Assignment Configuration Example287
  - Dynamic IP Address Assignment Configuration Example289
- DHCP Relay Agent Configuration Example293
- DHCP Snooping Configuration Example295
Managing Services298
- Overview298
- Configuring Service Management299
Using Diagnostic Tools301
- Ping301
- Traceroute301
- Ping Operation301
- Traceroute Operation303
Configuring MAC Authentication305
- Overview305
- Using MAC Authentication with Other Features306
- Configuration Prerequisites307
- Configuration Procedure307
- Configuring MAC Authentication Globally307
- Configuring MAC Authentication on a Port309
- MAC Authentication Configuration Examples310
  - Local MAC Authentication Configuration Example310
  - ACL Assignment Configuration Example313
Configuring 802.1X322
- Overview322
- Configuration Prerequisites323
- Configuration Guidelines323
- Configuration Procedure324
- Configuring 802.1X Globally324
- Configuring 802.1X on a Port325
  - Configuring an 802.1X Guest VLAN327
  - Configuring an Auth-Fail VLAN328
- 802.1X Configuration Example329
- ACL Assignment Configuration Example335
Configuring Port Security344
- Overview344
  - Port Security Features344
  - Port Security Modes344
- Configuration Guidelines346
- Configuration Procedures346
- Configuring Global Settings for Port Security347
- Configuring Basic Port Security Control348
- Configuring Secure MAC Addresses349
- Configuring Advanced Port Security Control350
- Configuring Permitted Ouis352
- Port Security Configuration Examples352
  - Basic Port Security Mode Configuration Example352
  - Advanced Port Security Mode Configuration Example356
Configuring Portal Authentication362
- Overview362
- Configuring Portal Authentication369
- Portal Authentication Configuration Examples379
Configuring AAA401
- Overview401
  - AAA Application401
  - Domain-Based User Management402
- Configuration Prerequisites402
- Configuration Procedure403
- Configuring an ISP Domain403
- Configuring Authentication Methods for the ISP Domain404
- Configuring Authorization Methods for the ISP Domain406
- Configuring Accounting Methods for the ISP Domain407
- AAA Configuration Example409
Configuring RADIUS414
- Overview414
- Configuration Guidelines419
- Configuring RADIUS420
- RADIUS Configuration Example424
Configuring Users430
- Configuring a Local User430
- Configuring a User Group432
Managing PKI434
- Overview434
- Configuration Guidelines436
- Recommended Configuration Procedures436
  - Configuration Procedure for Manual Requests437
  - Configuration Procedure for Automatic Requests438
- Creating a PKI Entity439
- Creating a PKI Domain440
- Generating an RSA Key Pair443
- Destroying the RSA Key Pair444
- Retrieving and Displaying a Certificate444
- Requesting a Local Certificate446
- Retrieving and Displaying a CRL447
- PKI Configuration Example449
Configuring Port Isolation453
- Overview453
- Configuring a Port Isolation Group453
- Port Isolation Configuration Example456
Configuring Authorized IP459
- Configuration Procedure459
- Authorized IP Configuration Example460
  - Network Requirements460
  - Configuration Procedure460
Configuring Acls463
- Overview463
- Configuration Guidelines465
- ACL Configuration Procedures465
Configuring Qos479
- Overview479
- Configuration Guidelines489
- Qos Configuration Procedures489
- Adding a Class491
- Configuring Classification Rules492
- Adding a Traffic Behavior495
- Configuring Traffic Mirroring and Traffic Redirecting for a Traffic Behavior496
- Configuring Other Actions for a Traffic Behavior497
- Adding a Policy500
- Configuring Classifier-Behavior Associations for the Policy500
- Applying a Policy to a Port501
- Configuring Queue Scheduling on a Port502
- Configuring Rate Limit on a Port503
- Configuring Priority Mapping Tables505
- Configuring Priority Trust Mode on a Port505
ACL and Qos Configuration Example508
- Network Requirements508
- Configuring Switch508
Configuring Poe518
- Overview518
- Poe Configuration Example521
Support and Other Resources524
- Contacting HP524
  - Subscription Service524
- Related Information524
  - Documents524
  - Websites524
- Conventions525
Index527

HP 830 Series User Manual

Table of Contents

Questions and Answers:

HP 830 Series Specifications

Related product manuals

Brand	HP
Model	830 Series
Category	Switch
Language	English