Korg Oasys - Sampling (Open Sampling System); Sampling Overview and Setup

Audio recording Song editing
115
WhenselectingaWAVEfile,youcanpressthePlay
buttontoauditionthefilestohelpyoufindthe
desiredone.
Youcanalsousethe“Name”fieldlocatedaboveto
assignanametotheregion.Editthe“Name”after
you’veselectedafile.
Note:TheOKbuttonisavailableonlyifyou’ve
selecteda48kHzmonauralWAVEfile.Ifyou’ve
selecteda44.1kHzfileora48kHzstereofile,the
buttonwillbegrayed‐outandyouwon’ tbeableto
pressit.
ThePlaybuttonisavailableonlyifyou’veselecteda
48kHzWAVEfile.
Editingaregionwillaffecttheaudiotrackforthe
entiresong.Usecautionwheneditingaregionthat’s
alreadyusedinanaudiotrack.
7. PresstheOKbutton,theselectedregionwillbe
placedintheaudiotrack.
8. Selecttheeventthatyouwanttoedit,andusethe
locationparameters“Measure”and“BeatTick”to
editthelocationoftheevent.
Youcan’tplacetwoormoreeventsatthesame
location.
9. PresstheDonebutton.
10.PresstheSEQUENCERSTART/STOPswitch,and
makesurethattheWAVEfileplaysback.
YoucanpresstheCOMPAREswitchtoreturntothe
stateprior
totheedityoujustperformed.
We’vekeptthisexamplesimple,butyoucanalso
performeditingoperationssuchaschangingthe
playbackpositionoftheWAVEfileinstepsofasingle
sample,changingthelocationrelativetoananchor
point,orcrossfadingtwoaudioevents.Formore
information,see
“A u d i o AutomationEdit”onpage 599
oftheParameterGuide.
Song editing
Youcanapplyavarietyofeditingoperationstoasong.
Theavailabletypesofeditingoperationarelisted
below.
Song
DeleteSong:Thiscommanddeletesthecurrently
selectedsong.Formoreinformation,see“DeleteSong”
onpage 582oftheParameterGuide.
CopyFromSong:Thiscommandcopiesallofthe
settingdataandmusicaldatafromthespecifiedsong
tothecurrentlyselectedsong.Formoreinformation,
see“CopyFromSong”
onpage 582oftheParameter
Guide.
FF/REWSpeed:Thisallowsyoutosetthespeedat
whichfast‐forwardorrewindwilloccurwhenyou
presstheFFswitchorREWswitch.Formore
information,see“FF/REWSpeed”onpage 583ofthe
ParameterGuide.
GMInitialize:ThiscommandtransmitsaGMSystem

OnmessagetotheSequencermode,resettingallMIDI
trackstotheGMsettings.Formoreinformation,see
“GMInitialize”onpage 584oftheParameterGuide.
AutoHDR/SamplingSetup:Thiscommand
automaticallymakestheappropriatetwo‐channelmix
settingsetc.forharddiskrecording,audiotrack
bouncing,sampling/resampling(in‐tracksampling,

etc.),orcreatinganaudioCD.Formoreinformation,
see“A u t o HDR/SamplingSetup”onpage 587ofthe
ParameterGuide.
Initialize:Setparametersrelatedtoharddisk
recordingandsamplingtotheirdefaultvalues.
HDR(AudioTrackRecording):Makethenecessary
settingsforrecordingexternalaudiosignalssuchas
guitarorvocal
fromtheaudioinputstoaudio
tracks.
BounceAudioTrack:Makethenecessarysettings
forbounce‐recordingaudiotracks.
2chMixtoDisk:Makesettingsforresamplinga
completedsonginordertocreateatwo‐channel
stereoWAVEfileontheharddisk.(Usethisifyou
wanttocreateaWAVEfileandthenusetheDisk
modeMakeAudioCDpagetoburnthefiletoan
audioCDontheinternalCD‐R/RWdrive.)