Korg Oasys - Using the CD-R;RW Drive; Turning the Power off

Setup Using the CD-R/RW drive
45
3. RaisetheOASYS’sVOLUMEslidertoan
appropriatelevel,andadjustthevolumeofyour
poweredmonitorsorstereoamp.
Afteryou’veturnedoffthepower,youmustwait
approximatelytensecondsbeforeturningthe
poweronagain.
Tip:Youcansetthe“PowerOnMode”(GlobalP0:
SystemPreferencepage)so
thatthemodeandpage
thathadbeenselectedwhenyouturnedthepoweroff
willappearwhenthepoweristurnedon.
Formoreinformation,see“Recallingthelast‐selected
modeandpageatpower‐on”onpage 152.
Leaving or deleting WAVE files in the TEMP
folder
IfyourecordaudiotracksinSequencermodeandthen
turnoffthepowerwithoutsavingthesong,theWAVE 
fileswillremainintheTEMPfolderoftheinternal
harddisk.Ifthisoccurs,thefollowingdialogboxwill
appearthenexttimeyoupower‐on,askingyou
whetheryou
wanttodeletetheseWAVE filesorsave
them:
Thereareun‐savedaudiofilesfromyourprevious
recordingsession.
Doyouwanttorestorethesefiles,ordeletethemfrom
thedisk?
[Restore][Delete]
Ifyoudon’tintendtousetheWAVEfiles,we
recommendthatyoudeletethemsothey
don’twaste
spaceontheinternalharddisk.Todeletethem,press
theDeletebutton.
Ifyouwanttousethesefilesinanewsongetc.,press
theRestorebuttontokeepthem.
Formoreinformation,see“Howaudiodataisstored
onthedisk”onpage 102.
LCD screen display when options are
installed
IfyouinstalltheEXB‐DIoptionintheOASYS,the
EXB‐DIwillbeaddedtotheindicationsinthe
“Options”areaofthescreen.AfterinstallingtheEXB‐
DI,besuretocheckthisscreentoseewhetherthis
indicationappears.Ifthisindicationdoesnotappear
eventhough
you’veinstalledtheEXB‐DI,itwasnot
installedcorrectly.Turnoffthepowerandreinstallthe
EXB‐DI.
Fordetails,see“EXB‐DIoptionboard,additional
memory,&calendarbattery”onpage 1089ofthe
ParameterGuide.
2. Turning the power off
1. SetthefrontpanelVOLUMEsliderandthe
volumeofyourpoweredmonitororstereoampto
zero.
2. Turnoffthepowerofyourpoweredmonitoror
stereoamp.
3. PresstheOASYS’sPOWERswitchtoturnoffthe
power.
Neverturnoffthepowerwhiledataisbeingwritten
intointernalmemory.
While
dataisbeingwritten,theLCDscreenwill
indicate“Nowwritingintointernalmemory.”Data
iswrittenintointernalmemorybythefollowing
operations.
•Writing(updating)aProgram,Combination,
GlobalSetting,DrumKits,orWaveSequences
•LoadingProgram,Combination,GlobalSetting,
DrumKit,orWaveSequencesdatainDiskmode
• Receivinga
MIDIdatadumpforProgram,
Combination,GlobalSetting,DrumKit,orWave
Sequences
•WhenusingSamplingmodemenucommands
(“MoveSample,”“MoveMS,”“ConvertMSTo
Program,”“TimeSlice,”etc.)tosimultaneously
modifyprogramsordrumkits.
•WhensamplingtoRAMinProgram,Combination,
orSequencermode,ifyousimultaneouslyconvert
thesampletoaprogram.
Neverturnoffthepowerwhilemediasuchasthe
harddiskisbeingaccessed,suchaswhile
recordingorplayingaudiotracks,orsamplingfor
anextendedtimeontheharddisk.Turningoffthe
powerwhilediskaccessisoccurringmayrenderthe
media
unusable.
Using the CD-R/RW drive
Inserting a disc
MakesurethattheOASYSison.
1. PresstheejectbuttonoftheCD‐R/RWdriveto
openthedisctray.
Atthistime,thetraywillopenonlyhalfway.You
mustmanuallypullthetrayoutcompletelybefore
placingadisconit.
WhenopeningtheCD‐R/RWdriveforthe
firsttime,
removethepickupstopperfromthedisctraybefore
usingthedrive.
2. Placethediscaccuratelyinthetray,labelsideup.
3. Pushthedisktrayinuntilitiscompletelyclosed.
Removing a disc
1. Presstheejectbuttontoopenthedisctray.
Thetraywillopenabouthalfway.Manuallypullthe
trayoutfarenoughtoremovethediscfromthetray.
2. Gentlyremovethediscfromthedisctray.
3. Pushthedisctrayinuntilitiscompletelyclosed.
Emergency disc removal
Normallyyouwillbeabletoremovethediscas
describedabove.However,ifthisisnotpossibledueto
apowerfailureorotherproblem,youcanalsoremove
thediscasfollows.