Korg Oasys - Program;Combination and Song Playback Issues

Overview - What is KARMA? KARMA function settings
213
Withtheappropriate“A S S I G N ” settings,aGE
realtimeparameterof(forexample)moduleAcan
controlledindependentlybyMasterandModuleA.
Forexampleyoucanmakesettingssothatthe
SwingparameterofadrumGEonmoduleAis
controlledinMASTERbyslider1overarangeof
0–
50%,andinMODULEAbyslider1overarangeof
50–100%.
Master:0–50%
ModuleA:50–100%
Inthiscase,ifyouswitchMODULECONTROL
betweenMASTERandAwhileusingslider1to
controltheparameter,theparameterwilloperatein
itslast‐controlledstate.IfyousetSwing
to0%in
MASTER,andthenswitchtomoduleA,Swingwill
remainat0%aslongasyoudon’tmoveslider1.
HoweverSwingwillchangeonceyoumoveslider1
tocontroltheparameterintherangeof50–100%.
1. SetMODULECONTROLtoMASTER,andset
slider1to
theminimumposition.→“Swing”
operatesat0%.
2. ChangeMODULECONTROLtoA.→“Swing”
operatesat0%.
3. Moveslider1tothemaximumposition.→
“Swing”operatesat100%.
Theinternalsettingsareautomaticallycontrolledso
thatthephrasebeinggenerateddoesnotchange
abruptly.Intheaboveexamplewhenyou
use
MASTERtoset“Swing”to0%andthenswitchto
moduleA,thedisplayedindicationis50–100%but
theparameterisactuallyoperatingatavalueof0%.
Inthisway,youneedtobeawarethatthedisplayed
indicationmaynotmatchtheactualresult.
Perf RTP (Perf Real-Time Parameters)
Inthesamewayasforaprogram,KARMAfunction
parametersotherthanGErealtimeparameters(e.g.,
KARMAmoduleparameters)canalsobeassignedto
controllers.
ThesesettingsarevalidwhenMODULECONTROLis
settoMASTER.
1. AccesstheCombinationP7:KARMA–PerfReal‐
TimeParameterspage.
Inthesamewayas
foraprogram,set“Group,”
“Parameter,”“Min,”“Max,”“Value,”“A s s i g n , ” and
“Polarity.”Inacombination,youcanusethefour
KARMAmodulesA,B,C,andD.
Turnon(check)the“A , ” “B,”“C,”and/or“D”boxes
toselectthemodule(s)youwanttocontrol.
Intheaboveexample,KARMAREALTIME
CONTROLS
switches1,2,3,and4arecontrolling
theRun/MutesettingofmodulesA,B,C,andD
respectively.
Dynamic MIDI settings
Youcanmakethesesettingsinthesamewayasfora
program.Formoreinformation,see“DynamicMIDI
Sources&Destinations”onpage 1038oftheParameter
Guide.
Naming the KARMA RTC sliders 1–8 and switches
1–8 for MASTER and module A–D
Inthesamewayasforaprogram,youcanselectnames
fortheKARMACONTROLSslidersandKARMA
SWITCHES.Thesesettingsaresavedaspartofthe
combination.
Inacombination,theareainsquarebrackets[]
automaticallyshowsaportionofthecategorynameof
theprogramselectedfor
eachtimbrecontrolledbythe
KARMACONTROLSslidersandKARMA
SWITCHES.Thisletsyouknowthetimbrewhose
phraseisbeingcontrolledbyeachKARMA
CONTROLSsliderandKARMASWITCH.
Ifmorethanonetimbreisbeingcontrolled,theareain
squarebracketswillindicate“MLTI.”
MODULE
C
ONTROL
MASTER
A
B
C
D
KARMA module [D]
KARMA module [C]
KARMA module [B]
KARMA module [A]
KARMA REALTIME CONTROLS
KARMA SCENES
KARMA SWITCHES
KARMA CONTROLS
123
4
567
8