Kyocera TASKalfa 8002i

2WA/2NJ/2RK
3-40
1. DF main PWB ....................................... Controlling the electric parts.
2. DF staple relay PWB............................. Relaying the staple unit control signals.
3. DF operation PWB ................................ Consisting of LEDs and keys.
4. DF front cover switch ............................ Detecting the front cover open/close.
5. DF eject cover switch............................ Detecting the eject cover open/close.
6. DF paper entry sensor .......................... Detecting presence of paper at the paper entry section.
7. DF middle sensor.................................. Detecting presence of paper in the conveying section.
8. DF eject sensor..................................... Detecting presence of paper the eject section.
9. DF side registration sensor 1 ................ Detecting the adjusting DF plate front home position.
10. DF side registration sensor 2 ................ Detecting the adjusting DF plate rear home position.
11. DF paddle sensor.................................. Detecting the paddle home position.
12. DF drum sensor .................................... Paper detection at the relief drum.
13. DF adjusting sensor .............................. Detecting the paper guides home position.
14. DF bundle eject switch.......................... Detecting the bundle eject unit position.
15. DF tray upper surface sensor 1 ............ Detecting the DF main tray paper upper surface.
16. DF tray upper surface sensor 2 ............ Detecting the DF main tray paper upper surface.
17. DF tray sensor 1 ................................... Detecting the eject tray home position.
18. DF tray sensor 2 ................................... Detecting the eject tray home position.
19. DF tray sensor 3 ................................... Detecting the eject tray middle position.
20. DF tray sensor 4 ................................... Detecting the eject tray lower limit.
21. DF tray sensor 5 ................................... Detecting the eject tray lower limit.(when the folding unit is
installed)
22. DF slide sensor ..................................... Detecting the staple unit slide position.
23. DF shift set sensor ................................ Detecting the shift guide home position.
24. DF shift release sensor ......................... Detecting the shift guide release position.
25. DF shift sensor 1................................... Detecting the front shift plate home position.
26. DF shift sensor 2................................... Detecting the rear shift plate home position.
27. DF sub eject sensor .............................. Detecting paper ejected to the tray B.
28. DF sub tray full sensor .......................... Detecting tray B paper full.
29. DF paper entry motor............................ Driving the entry roller.
30. DF middle motor ................................... Driving the middle roller.
31. DF paddle motor ................................... Driving the paper guides.
32. DF eject release motor.......................... Driving the bundle eject unit.
33. DF side registration motor 1.................. Driving the adjusting plate front.
34. DF side registration motor 2.................. Driving the adjusting plate rear.
35. DF relief drum motor ............................. Driving the relief drum.
36. DF eject motor ...................................... Driving the eject roller.
37. DF tray motor ....................................... Eject tray ascending and descending drive.
38. DF slide motor....................................... Staple unit sliding drive.
39. DF shift release motor........................... Detecting the shift guide release position.
40. DF shift motor 1 .................................... Driving the rear shift guide.
41. DF shift motor 2 .................................... Driving the front shift guide.
42. DF feedshift solenoid 1 ......................... Switching the feedshift guide.
43. DF feedshift solenoid 2 ......................... Switching the feedshift guide.
44. DF feedshift solenoid 3 ......................... Switching the feedshift guide.
45. DF eject clutch ...................................... Driving the eject roller.
46. DF staple unit........................................ Paper stapler.
47. DF Eject fan motor 1 ............................. Cooling the eject paper.(rear) (not connected)
48. DF Eject fan motor 2 ............................. Cooling the eject paper.(front) (not connected)
49. DF Eject fan motor 3 ............................. Cooling the eject paper.(center) (not connected)