D.3 UL Standards
588 YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual
Note: Use crimp insulated terminals or insulated tubing for wiring these connections. Wires should have a continuous maximum
allowable temperature of 75C 600 V UL approved vinyl sheathed insulation. Ambient temperature should not exceed 40C.
Table D.6 Wire Gauge and Torque Specifications (Three-Phase 400 V Class)
2A0312
<5>
R/L1, S/L2, T/L3 95 2P 95 to 150 4/0 2P 3/0 to 300 80 2P 70 to 150
M12
32 to 40
(283 t
o 354)
U/T1, V/T2, W/T3 95 2P 95 to 150 3/0 2P 3/0 to 300 80 2P 70 to 200
–, +1 – 70 to 150 – 3/0 to 300 150 2P 80 to 150
+3 – 70 to 150 – 3/0 to 300 80 2P 80 to 150 M10
18 to 23
(159 t
o 204)
95 95 to 150 2 2 to 300 38 38 to 150 M12
32 to 40
(283 to 354)
2A0360
<5>
R/L1, S/L2, T/L3 240 95 to 300 250 2P 4/0 to 600 100 2P 80 to 325
M12
32 to 40
(283 t
o 354)
U/T1, V/T2, W/T3 240 95 to 300 4/0 2P 4/0 to 600 100 2P 80 to 325
–, +1 – 125 to 300 – 250 to 600 150 2P 125 to 325
+3 – 70 to 300 – 3/0 to 600 80 2P 80 to 325 M10
18 to 23
(159 t
o 204)
120 120 to 240 1 1 to 350 38 38 to 200 M12
32 to 40
(283 to 354)
2A0415
<5>
R/L1, S/L2, T/L3 120 2P 95 to 300 350 2P 250 to 600 125 2P 100 to 325
M12
32 to 40
(283 t
o 354)
U/T1, V/T2, W/T3 300 95 to 300 300 2P 300 to 600 125 2P 125 to 325
–, +1 – 150 to 300 – 300 to 600 200 2P 150 to 325
+3 – 70 to 300 – 3/0 to 600 100 2P 80 to 325 M10
18 to 23
(159 t
o 204)
120 120 to 240 1 1 to 350 60 60 to 200 M12
32 to 40
(283 t
o 354)
<1> Gauges listed here are for use in Europe and China.
<2> Gauges listed here are for use in the United States.
<3> Gauges listed here are for use in Asia except for China.
<4> When an EMC filter is installed, additional measures must be taken in order to comply with IEC/EN 61800-5-1. Refer to EMC Filter
Installation on page 580.
<5> Drive models CIMR-A2A0110 to 2A0415 require the use of closed-loop crimp terminals for UL/cUL compliance. Use only the tools
recommended by the terminal manufacturer for crimping.
Model
CIMR-A
Terminal
For Europe and China <1> For U.S.A. <2> For Asia <3>
Screw
Size
Tightening
Torque
Nm (lb.in.)
Recomm.
Wire Size
mm
2
Applicable
Gauge
mm
2
Recomm.
Gauge
AWG, kcmil
Applicable
Gauge
AWG, kcmil
Recomm.
Wire Size
mm
2
Applicable
Gauge
mm
2
4A0002
4A0004
R/L1, S/L2, T/L3 2.5 2.5 to 6 14 14 to 10 2 2 to 5.5
M4
1.2 to 1.5
(
10.6 to 13.3)
U/T1, V/T2, W/T3 2.5 2.5 to 6 14 14 to 10 2 2 to 5.5
–, +1, +2 – 2.5 to 6 – 14 to 10 2 2 to 5.5
B1, B2 – 2.5 to 6 – 14 to 10 2 2 to 5.5
2.5 2.5 to 4 12 14 to 12 2 2 to 5.5
4A0005
4A0007
4A0009
R/L1, S/L2, T/L3 2.5 2.5 to 6 14 14 to 10 2 2 to 5.5
M4
1.2 to 1.5
(10.6 to 13.3)
U/T1, V/T2, W/T3 2.5 2.5 to 6 14 14 to 10 2 2 to 5.5
–, +1, +2 – 2.5 to 6 – 14 to 10 2 2 to 5.5
B1, B2 – 2.5 to 6 – 14 to 10 2 2 to 5.5
2.5 2.5 to 6 10 14 to 10 3.5 2 to 5.5
4A0011
R/L1, S/L2, T/L3 2.5 2.5 to 6 12 14 to 10 2 2 to 5.5
M4
1.2 to 1.5
(
10.6 to 13.3)
U/T1, V/T2, W/T3 2.5 2.5 to 6 14 14 to 10 2 2 to 5.5
–, +1, +2 – 2.5 to 6 – 14 to 10 2 2 to 5.5
B1, B2 – 2.5 to 6 – 14 to 10 2 2 to 5.5
2.5 2.5 to 6 10 14 to 10 3.5 2 to 5.5
4A0018
R/L1, S/L2, T/L3 2.5 2.5 to 16 10 12 to 6 3.5 2 to 14
M4
2.1 to 2.3
(
18.6 to 20.4)
U/T1, V/T2, W/T3 2.5 2.5 to 16 10 12 to 6 3.5 2 to 14
–, +1, +2 – 4 to 16 – 12 to 6 3.5 2 to 14
B1, B2 – 4 to 6 – 12 to 10 2 2 to 5.5
2.5 2.5 to 6 10 14 to 10 3.5 2 to 5.5 M5
2.0 to 2.5
(17.7 to 22.1)
4A0023
R/L1, S/L2, T/L3 4 2.5 to 16 10 10 to 6 5.5 3.5 to 14
M4
2.1 to 2.3
(
18.6 to 20.4)
U/T1, V/T2, W/T3 4 2.5 to 16 10 10 to 6 5.5 3.5 to 14
–, +1, +2 – 4 to 16 – 12 to 6 5.5 3.5 to 14
B1, B2 – 4 to 6 – 12 to 10 2 2 to 5.5
4 4 to 6 10 12 to 10 3.5 3.5 to 5.5 M5
2.0 to 2.5
(
17.7 to 22.1)
Model
CIMR-A
Terminal
For Europe and China <1> For U.S.A. <2> For Asia <3>
Screw
Size
Tightening
Torque
Nm (lb.in.)
Recomm.
Wire Size
mm
2
Applicable
Wire Size
mm
2
Recomm.
Gauge
AWG, kcmil
Applicable
Gauge
AWG, kcmil
Recomm.
Wire Size
mm
2
Applicable
Wire Size
mm
2
To Next Page
Loading...
