YOKOGAWA DL6000 Series

18-12
IM DLM6054-01EN
Item Specifications
Cursor measurement he following cursors are selectable.

  , Marker, SerialMarker, Serial
Automated measurement of
waveform parameters
The following waveform parameters can be automatically measured.
Items that are measured over the entire specified range of data and are irrelevant to the period.
Max, Min, High, Low, P-P, High-Low, +Over, -Over, Rms, Mean, Sdev, IntegTY, Edge Count+Over, -Over, Rms, Mean, Sdev, IntegTY, Edge CountOver, -Over, Rms, Mean, Sdev, IntegTY, Edge Count-Over, Rms, Mean, Sdev, IntegTY, Edge CountOver, Rms, Mean, Sdev, IntegTY, Edge Count CountCount
Items that are measured in the first period in the specified range.
Freq, Period, Burst, +Width, -Width, Duty, Rise, Fall, Delay+Width, -Width, Duty, Rise, Fall, DelayWidth, -Width, Duty, Rise, Fall, Delay-Width, Duty, Rise, Fall, DelayWidth, Duty, Rise, Fall, Delay
Items that are measured over all periods in the specified range.
AvgPeriod, C. Rms, C. Mean, C. Sdev, C. IntegTY, C. Rms, C. Mean, C. Sdev, C. IntegTYSdev, C. IntegTYC. IntegTYIntegTY



For logic signal, only the following items are selectable.

                           , Delay
The maximum total number of items that can be displayed in Area1 and Area2 on the screen is 16.
Statistical processing of
waveform parameters
he following three types of statistical processing are available.
Continuous:: Calculates statistics on normal measurement that is performed multiple times.
Cycle:: Calculates statistics on the measurement of each period of the displayed
waveform.
History:: Calculates statistics on the measurements of multiple history waveforms.
The calculated statistics are as follows:
Statistical items: Max, Min, Mean, Sdev, Count
The maximum number of items that can be displayed on the screen is two.
Trend display and histogram
display of waveform
parameters
Up to two trends or histograms of the specified measurement items can be displayed.
The maximum number of items that can be displayed on the screen is 16.
Expanded waveform
parameter measurement
Automated measurement of waveform parameters can be performed on two areas. Calculations
can be performed using the automated measurement values of waveform parameters.
In addition to the normal waveform measurement range (Area1), you can specify another
measurement range (Area2).
The same parameter measurement as Area1 can be performed in Area2.
The maximum total number of items that can be displayed in Area1 and Area2 on the screen is 16.
Frequency distribution
analysis
Counts the frequency of data occurrence in a specified area and displays the values in a
histogram.
You can select whether to count the voltage data frequency or the time data frequency.
The mean, standard deviation, maximum value, minimum value, peak value, median, etc., can be
measured on the histogram.
You can set up to two histogram source waveforms.
Action-on-trigger A specific action can be executed when the DL6000/DLM6000 triggers.
You can set the number of times to execute the action in terms of the number of waveform
acquisitions or the number of determinations.
Actions:: Beeping, screen capture data printing or saving, waveform data saving, mail
transmission
2
GO/NO-GO determination A specific action can be executed when the GO/NO-GO result is NO-GO.
You can set the number of times to execute the action in terms of the number of waveform
acquisitions or the number of determinations.
Up to four conditions can be set, and the four4 conditions can be combined using AND or OR logic
to perform determination.
Reference condition can be set to whether the source waveform enters the reference range (IN),
moves outside the search range (OUT), or don't care (X).
The following four reference range types are available.
Rect-Zone:: Rectangular zone. FFT waveforms cannot be used.
Wave-Zone:: Waveform zone. XY and FFT waveforms cannot be used.
Polygon-
Zone::
Polygonal zone. FFT waveforms cannot be used.
Parameter:: Zone between the upper and lower limits of one waveform parameter.
Actions: Beeping, screen capture data printing or saving, waveform data saving, mail
transmission
1
1 CAN, LIN, UART, I
2
C, and SPI are options.
2 On models with the Ethernet option.
18.5 Features