Doc ID :ADR233B/IM/01
Ref ID : ADR233B/IM/UG
Rev No. : 05
ADR233B
8.4.7.1 CT/VT Ratios – System Config 295
8.4.8 PROTECTIONS 298
8.4.9 CLEAR RECORDS 302
8.4.9.1 Clear Records 302
8.4.10 OUTPUT & LED TEST 304
8.4.10.1 Output & LED Test 304
8.4.11 Group 1 306
8.4.11.1 Group 1 – Menu List 306
8.4.11.2 Equipment Data 309
8.4.11.3 Ph Differential 313
8.4.11.3.1 Ph Differential (If Disabled) 313
8.4.11.3.2 Ph Differential (If Enabled) 314
8.4.11.4 REF 319
8.4.11.4.1 REF (If Disabled) 319
8.4.11.4.2 REF (If LowZ) 320
8.4.11.4.3 REF (If HighZ) 322
8.4.11.5 Phase OC 324
8.4.11.5.1 W1 Phase OC (IF Disabled) 324
8.4.11.5.2 W1 Phase OC (If IEC/ UK Curve is selected) 326
8.4.11.5.3 W1 Phase OC (If IEEE / US Curve is selected) 329
8.4.11.5.4 W1 Phase OC (If Definite Time is selected) 332
8.4.11.6 Ground OC 335
8.4.11.6.1 Ground OC (If Disabled) 335
8.4.11.6.2 Ground OC (If IEC Curve is selected) 336
8.4.11.6.3 Ground OC (If IEEE / US Curve is selected) 339
8.4.11.6.4 Ground OC (If Definite Time is selected) 342
8.4.11.7 Residual OC 345
8.4.11.7.1 W1 Residual OC (If Disabled) 345
8.4.11.7.2 W1 Residual OC (If IEC Curve is selected) 347
8.4.11.7.3 Residual OC (If IEEE / US Curve is selected) 350
8.4.11.7.4 Residual OC (If Definite Time is selected) 353
8.4.11.8 Sequence OC 356
8.4.11.8.1 W1 Sequence OC (If Disabled) 356
8.4.11.8.2 Sequence OC (If IEC Curve is selected) 358
8.4.11.8.3 Sequence OC (If IEEE / US Curve is selected) 361
8.4.11.8.4 Sequence OC (If Definite Time is selected) 364
8.4.11.9 Under Voltage 367
8.4.11.9.1 To Set – Under Voltage (If Disabled) 367
8.4.11.9.2 To Set – Under Voltage (If Enabled) 368
8.4.11.10 Over Voltage 369
8.4.11.10.1 To Set – Over Voltage (If Disabled) 369
8.4.11.10.2 To Set – Over Voltage (If Enable) 370
8.4.11.11 V/Hz Protection 372
8.4.11.11.1 V/Hz Protection (If Disabled) 372
8.4.11.11.2 V/Hz Protection (If Enabled) 373
8.4.11.12 Breaker Failure 375
8.4.11.12.1 To Set – W1 50BF (If Disabled) 375
8.4.11.12.2 To Set – W1 50 BF (If Enabled) 376
To Next Page
Loading...
