BONFIGLIOLI Agile

Content
7.3.4 Auto start ............................................................................................................... 129
7.3.5 Flying Start ............................................................................................................. 129
7.3.6 Direct current brake ................................................................................................ 131
7.3.7 Positioning ............................................................................................................. 132
7.4 Error and warning behavior .................................................................................... 135
7.4.1 Overload Ixt ........................................................................................................... 135
7.4.2 Temperature .......................................................................................................... 136
7.4.3 Controller status ..................................................................................................... 136
7.4.4 Frequency switch-off limit ........................................................................................ 137
7.4.5 External error ......................................................................................................... 137
7.4.6 Motor temperature .................................................................................................. 137
7.4.6.1 Technical demands on measuring resistors ......................................................... 140
7.4.7 Phase failure .......................................................................................................... 141
7.4.8 Automatic Error Acknowledgment ............................................................................. 142
7.5 Reference Values .................................................................................................... 142
7.5.1 Reference frequency channel ................................................................................... 142
7.5.1.1 Limits .............................................................................................................. 145
7.5.1.2 Positive and negative reference frequencies ........................................................ 145
7.5.1.3 Fixed frequencies ............................................................................................. 146
7.5.1.4 Ramps ............................................................................................................. 147
7.5.1.5 Blocking frequencies ......................................................................................... 150
7.5.1.6 JOG frequency ................................................................................................. 151
7.5.2 Reference percentage channel ................................................................................. 151
7.5.2.1 Limits .............................................................................................................. 154
7.5.2.2 Positive and negative reference percentages ....................................................... 154
7.5.2.3 Fixed percentages ............................................................................................ 154
7.5.2.4 Ramps ............................................................................................................. 155
7.5.3 Motor potentiometer ............................................................................................... 156
7.5.3.1 Operation modes of motor potentiometer ........................................................... 156
7.5.3.2 Ramp of motor potentiometer ........................................................................... 156
7.5.3.3 Motor potentiometer via digital inputs ................................................................ 157
7.5.3.4 Keypad motorpoti: Control via operator panel ..................................................... 160
7.5.4 Electronic gear ........................................................................................................ 163
7.5.4.1 Scope of function ............................................................................................. 163
7.5.4.2 Operation modes of electronic gear .................................................................... 163
7.5.4.3 Gear factor ...................................................................................................... 165
7.5.4.4 Offset .............................................................................................................. 166
7.5.4.5 Actual values ................................................................................................... 166
7.5.4.6 Adjustment Options .......................................................................................... 166
7.6 Control inputs and outputs ..................................................................................... 168
7.6.1 Multifunction input MFI1 .......................................................................................... 168
7.6.1.1 Multifunction input set as analog input MFI1A ..................................................... 169
7.6.1.2 Multifunction input set as digital input MFI1D ...................................................... 174
7.6.2 Multifunction input MFI2 .......................................................................................... 175
7.6.2.1 Multifunction input set as analog input MFI2A ..................................................... 175
7.6.2.2 Multifunction input set as digital input MFI2D ...................................................... 181
7.6.3 Multifunction output MFO1 ....................................................................................... 182
7.6.4 Digital input/output IN3D/OUT3D ............................................................................. 186
7.6.5 Digital outputs ........................................................................................................ 187
7.6.5.1 Digital message ................................................................................................ 189
7.6.5.2 Setting frequency ............................................................................................. 190
7.6.5.3 Reference value reached ................................................................................... 190
7.6.5.4 Flux forming finished ........................................................................................ 191
7.6.5.5 Release brake .................................................................................................. 192
7.6.5.6 Current limitation ............................................................................................. 192
7.6.5.7 External fan ..................................................................................................... 192
7.6.5.8 Warning mask .................................................................................................. 192
7.6.5.9 Warning mask, application ................................................................................ 195
6
Operating Instructions
Agile 06/2013 This document