Cisco ASR 1002 Hardware Installation Guide

Cisco ASR 1000-ESP200
Cisco ASR1000-ESP200 is a CPP-based embedded services processor for the Cisco ASR1000 Series Routers.
It is a field-replaceable unit (FRU), and it is capable of supporting online insertion and removal (OIR) operations
in conjunction with one or two route processors, a secondary embedded services processor, and up to six SPA
carrier cards.
Cisco ASR 1000-ESP200 is supported on the Cisco ASR 1013 Router.
Cisco ASR1000-ESP200 provides the following features:
•
24 configurable ESI links for SPA Carrier Card and native Line Card support:
◦
ESI links support with a bandwidth of up to 46 Gbps for the Cisco ASR 1013 Router on Sip slots
0,1,4, and 5.
◦
ESI links support with a bandwidth of up to 110 Gbps for the Cisco ASR 1013 Router on Sip slots
2 and 3.
It can support at least 40 Gbps of aggregated security traffic.
All Cisco ASR 1000 Series embedded services processors are based on a common highly-programmable
network Cisco QuantumFlow Processor (packet processing). The Cisco ASR 1013 Router slots are keyed
using rotated guide pins so that plug-in cards can only be fully inserted in slots where they are intended to
operate. This keying prevents cards from making midplane contact in slots the cards are not allowed.
Cisco ASR 1000-ESP200 and Third Generation Cisco QFP
Each Cisco ASR 1000-ESP200 uses 4 third generation Cisco QFPs (QFP-3rd-Gen) Application Specific
Integrated Circuits (ASICs) to achieve maximum performance. Each QFP-3rd-Gen ASIC is mapped with a
subset of SPA bays and interfaces (SIP). Through this mapping, the Cisco ASR 1000-ESP200 can perform
all baseline packet routing operations such as Quality of Service (QoS) classification and IP multicasting.
They can also perform Network Address Translation (NAT) tasks.
Cisco ASR 1000 Series Router Hardware Installation Guide
91
Cisco ASR 1000 Series Routers Embedded Services Processors
Cisco ASR 1000-ESP200

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g