Cisco ASR 1002 Hardware Installation Guide

• System up with RP running older CPLD and RP with older CPLD inserted—The message will be printed
when the system powered up before this event. When the second RP is inserted, similar message for the
new card will be printed.
When To Perform a CPLD Upgrade
In order to use existing ASR1000-RP2 and ASR1000-SIP10 hardware components in the Cisco ASR 1013
Router, you must perform a CPLD upgrade on the RP2 and SIP10 components (with older CPLD) if the
following configurations occur:
• System powering up with both RPs with older CPLD—The system comes up in redundant mode and
the message stating that the CPLD needs upgrade (for both RPs) displays on the console with a clear
warning that the system may not work properly unless it is upgraded, and a summary of the instructions
to upgrade. A message for standby RP will appear in the standby console and the active RP.
• System powering up with one RP with older CPLD—The message will be printed for the RP with older
CPLD.
• System powering up with RP running latest CPLD and RP with older CPLD inserted—The message
will be printed for the newly inserted RP.
• System powering up with RP running older CPLD and RP with latest CPLD inserted—The message
will be printed when the system powered up before this event. When the second RP is inserted no special
action is taken.
• System up with RP running older CPLD and RP with older CPLD inserted—The message will be printed
when the system powered up before this event. When the second RP is inserted, similar message for the
new card will be printed.
Unsupported Standby ASR1000-RP2 or ASR1000-SIP10 Requires Upgrade
This section describes what happens when a standby Cisco ASR1000-RP2 or Cisco ASR1000-SIP10 with an
older version of CPLD is inserted into the Cisco ASR 1013 Router. The error message that is displayed on
the console and the message explanation and recommended action are described.
Error message
CMRP-2-FRU_CPLD_INCOMPATIBLE: [chars] in slot [chars] has been held in reset as its CPLD
firmware version is incompatible with [chars]
fru_model_string: ASR1000-RP2/ASR1000-SIP10
fru_string: [0-5]/R0/R1
hw_config_string: ASR1013
Reason
This FRU requires a newer CPLD firmware to function properly in this chassis.
Recommended action
Upgrade the CPLD firmware on this FRU using the upgrade hw-programmable CPLD file <pkg_file> slot
<fru_slot> command. For more details, see Upgrading Field Programmable Hardware Devices for Cisco ASR
1000 Series Routers .
Cisco ASR 1000 Series Router Hardware Installation Guide
35
Cisco ASR 1000 Series Routers Component Overview
Upgrading Existing Hardware Components to Support the Cisco ASR 1013 Router

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g