Cisco ASR 1002 Hardware Installation Guide

•
Your PC terminal emulation program is configured for 9600 baud, 8 data bits, 1 stop bit, no parity, and
flow control is set to none.
•
You have selected passwords for access control.
•
Captive installation screws are tight on all removable components.
•
The console terminal is turned on.
•
You have determined the IP addresses for the Ethernet and serial interfaces.
•
Empty card slots or card bays are filled with card blanks. This ensures proper air flow through the chassis
and electromagnetic compatibility (EMC).
You are now ready to start your router.
Verifying Power Supply Operation
Follow this procedure to verify power supply is operating correctly.
SUMMARY STEPS
1.
Check that the power supply LEDs are:
2.
To ensure that the power supply state is OK, type the show platform command. This output sample is
from the Cisco ASR 1013 router. The other Cisco ASR 1000 routers display similar type of output.
DETAILED STEPS
Step 1
Check that the power supply LEDs are:
•
INPUT OK is green
•
FAN OK is green
•
OUTPUT FAILED is not illuminated
Step 2
To ensure that the power supply state is OK, type the show platform command. This output sample is from the Cisco
ASR 1013 router. The other Cisco ASR 1000 routers display similar type of output.
The following output displays:
Example:
Router# show platform
Chassis type: ASR1013
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1000-SIP40 ok 22:56:46
0/0 SPA-5X1GE-V2 ok 22:55:42
0/1 SPA-5X1GE-V2 ok 22:55:36
0/2 SPA-5X1GE-V2 ok 22:55:32
0/3 SPA-5X1GE-V2 ok 22:55:28
1 ASR1000-SIP40 ok 22:56:46
1/0 SPA-5X1GE-V2 ok 22:55:43
1/1 SPA-5X1GE-V2 ok 22:55:40
1/2 SPA-5X1GE-V2 ok 22:55:35
Cisco ASR 1000 Series Router Hardware Installation Guide
462
Cisco ASR 1000 Series Routers Power Up and Initial Configuration
Verifying Power Supply Operation

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g