Cisco ASR 1002 Hardware Installation Guide

Installing the Cisco ASR 1001 Router in a Rack
After installing the rack-mount brackets on the chassis, you mount the chassis by securing the rack-mount
brackets to two posts or mounting strips in the rack using the screws provided. Because the rack-mount brackets
support the weight of the entire chassis, be sure to use all screws to fasten the two rack-mount brackets to the
rack posts.
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions
to ensure that the system remains stable. The following guidelines are provided to ensure your safety:
Note
•
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.When mounting
this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component
at the bottom of the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the
unit in the rack. Statement 1006
We recommend that you allow at least 1 or 2 inches (2.54 or 5.08 cm) of vertical clearance between the router
and any equipment directly above and below it.
To install the chassis in the rack, perform the following steps:
SUMMARY STEPS
1.
On the chassis, ensure that all screw fasteners on the installed components are securely tightened.
2.
Make sure that your path to the rack is unobstructed. If the rack is on wheels, ensure that the brakes are
engaged or that the rack is otherwise stabilized. See the next sections on the types of racks you can use to
install the chassis.
3.
(Optional) Install a shelf in the rack to support the Cisco ASR 1001 Router. If you use a shelf, this will
help support the chassis while you secure it to the rack.
4.
With two people, lift the chassis into position between the rack posts.
5.
Align the mounting bracket holes with the rack post holes and attach the chassis to the rack.
6.
Position the chassis until the rack-mounting flanges are flush against the mounting rails on the rack.
7.
Hold the chassis in position against the mounting rails in the equipment rack and follow these steps:
8.
Tighten all screws on each side to secure the chassis to the equipment rack.
DETAILED STEPS
Step 1
On the chassis, ensure that all screw fasteners on the installed components are securely tightened.
Step 2
Make sure that your path to the rack is unobstructed. If the rack is on wheels, ensure that the brakes are engaged or that
the rack is otherwise stabilized. See the next sections on the types of racks you can use to install the chassis.
Step 3
(Optional) Install a shelf in the rack to support the Cisco ASR 1001 Router. If you use a shelf, this will help support the
chassis while you secure it to the rack.
Step 4
With two people, lift the chassis into position between the rack posts.
Step 5
Align the mounting bracket holes with the rack post holes and attach the chassis to the rack.
Cisco ASR 1000 Series Router Hardware Installation Guide
432
Cisco ASR 1001 Router Overview and Installation
Installing the Cisco ASR 1001 Router in a Rack

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g