Cisco ASR 1002 Hardware Installation Guide

If there are two different versions of the Cisco ASR1000-ESP in a router when you reload, the F0 slot always
comes up as Active and the F1 slot comes up as Standby or Disabled, depending on whether the F1 slot has a
later version of the Cisco ASR1000-ESP or an earlier one. A downgrade from a later version ESP to an earlier
version is not supported and that is the reason the Cisco ASR1000-ESP20 is disabled in this step. To downgrade
back to a Cisco ASR1000-ESP20, you must remove the Cisco ASR1000-ESP40 and reload the router. Similarly,
to downgrade back to a Cisco ASR1000-ESP10 from a Cisco ASR1000-ESP20, you must remove the Cisco
ASR1000-ESP20 and reload the router.
Note
Removing a Cisco ASR1000-ESP
To remove the Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, Cisco ASR1000-ESP20, or Cisco
ASR1000-ESP40 from the Cisco ASR 1000 Series Routers, follow this procedure:
SUMMARY STEPS
1.
Slip on the ESD-preventive wrist strap that was included in the accessory kit. Loosen the captive screws
on the Cisco ASR 1000 Series Embedded Services Processor.
2.
Using the handles on both sides of the module, with two hands gently slide the Cisco ASR 1000 Series
Embedded Services Processor (ESP5, ESP10, ESP20, ESP40) out of the chassis slot.
3.
Place the Cisco ASR1000-ESP module on an antistatic surface with its printed circuit board components
facing upward or in a static shielding bag.
DETAILED STEPS
Step 1
Slip on the ESD-preventive wrist strap that was included in the accessory kit. Loosen the captive screws on the Cisco
ASR 1000 Series Embedded Services Processor.
Step 2
Using the handles on both sides of the module, with two hands gently slide the Cisco ASR 1000 Series Embedded
Services Processor (ESP5, ESP10, ESP20, ESP40) out of the chassis slot.
Handle the Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, Cisco ASR1000-ESP20, or Cisco ASR1000-ESP40
by the carrier edges only; never touch the printed circuit board components or connector pins.
Note
Step 3
Place the Cisco ASR1000-ESP module on an antistatic surface with its printed circuit board components facing upward
or in a static shielding bag.
What to Do Next
You have completed the removal procedure for the Cisco ASR 1000 Series Embedded Services Processor.
from a Cisco ASR1000-ESP.
Replacing the Cisco ASR1000-ESP
To replace the Cisco ASR 1000 Series Embedded Services Processor in the Cisco ASR 1000 Series Router,
follow this procedure:
Cisco ASR 1000 Series Router Hardware Installation Guide
532
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing a Cisco ASR1000-ESP

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g