Cisco ASR 1002 Hardware Installation Guide

Safety Compliance and NEBS Requirements
To comply with the Telcordia GR-1089
NEBS standard for electromagnetic
compatibility and safety, for Ethernet
RJ-45 ports, use only shielded Ethernet
cables that are grounded on both ends. In
a NEBS installation, all Ethernet ports are
limited to intrabuilding wiring.
CautionTelcordia NEBS GR-1089-Core Statement
GR-1089
GR-63
The English warnings in this document are followed by a statement number. To see the translations of a
warning into other languages, look up its statement number in http://www.cisco.com/en/US/docs/routers/
asr1000/rcsi/asr1rcsi.html Regulatory, Compliance, and Safety Information for the Cisco Aggregation
Services Router 1000 Series .
Note
Cautions and Regulatory Compliance Statements for NEBS
The following table lists cautions, regulatory compliance statements, and requirements for the Network
Equipment-Building System (NEBS) certification from the Telcordia Electromagnetic Compatibility and
Electrical Safety – Generic Criteria for Network Telecommunications Equipment (A Module of LSSGR,
FR-64; TSGR, FR-440; and NEBSFR, FR-2063) Telcordia Technologies Generic Requirements,
GR-1089-CORE.
Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.
To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety, for
Ethernet RJ-45 ports, use only shielded Ethernet cables that are grounded on both ends. In a NEBS
installation, all Ethernet ports are limited to intrabuilding wiring.
Caution
The intrabuilding ports of the equipment or subassembly is only suitable for connection to intrabuilding
or unexposed wiring or cabling. The intrabuilding ports of the equipment or subassembly MUST NOT
be metallically connected to interfaces that connect to the OSP or its wiring. These interfaces are designed
for use only as intrabuilding interfaces (Type 2 or Type 4 ports as described in GR-1089-CORE), and
require isolation from the exposed OSP cabling. The addition of primary protectors is not sufficient
protection in order to connect these interfaces metallically to OSP wiring.
Caution
Products that have an AC power connection are intended for deployments where an external surge protective
device (SPD) is used at the AC power service equipment as defined by the National Electric Code (NEC).
This product is designed for a common bonding network (CBN) installation.
Cisco ASR 1000 Series Router Hardware Installation Guide
114
Preparing Your Site for Installation
Cautions and Regulatory Compliance Statements for NEBS

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g