Cisco ASR 1002 Hardware Installation Guide

Removing the Cisco ASR 1000 SPA Interface Processor
To remove a SPA Interface Processor (SIP) in the Cisco ASR 1006 Router and Cisco ASR 1004 Router,
follow these steps.
SUMMARY STEPS
1.
Slip on the ESD-preventive wrist strap that was included in the accessory kit. Loosen the captive screws
on the Cisco ASR 1000 Series SPA Interface Processor.
2.
Using the handles on both sides of the module, with two hands gently slide the Cisco ASR 1000 Series
SPA Interface Processor out of the chassis slot.
3.
Place the Cisco ASR1000-SIP10 on an antistatic surface with its printed circuit board components facing
upward or in a static shielding bag.
DETAILED STEPS
Step 1
Slip on the ESD-preventive wrist strap that was included in the accessory kit. Loosen the captive screws on the Cisco
ASR 1000 Series SPA Interface Processor.
Step 2
Using the handles on both sides of the module, with two hands gently slide the Cisco ASR 1000 Series SPA Interface
Processor out of the chassis slot.
Handle the Cisco ASR1000-SIP10 by the card edges only; never touch the printed circuit board components or
connector pins.
Note
Step 3
Place the Cisco ASR1000-SIP10 on an antistatic surface with its printed circuit board components facing upward or in
a static shielding bag.
For detailed information about installing and removing SIPs and SPAs, see Cisco ASR 1000 Series Aggregation Services
Routers SIP and SPA Hardware Installation Guide .
What to Do Next
You have completed the removal procedure for the Cisco ASR1000-SIP10.
Replacing the Cisco ASR 1000 SPA Interface Processor
To replace a SPA Interface Processor (SIP), follow these steps.
SUMMARY STEPS
1.
Before inserting a SIP, make sure that the chassis is grounded.
2.
To insert the SIP, carefully align the edges of the SIP between the upper and lower edges of the router
slot.
3.
Carefully slide the SIP into the router slot until the SIP makes contact with the backplane.
4.
Tighten the locking thumbscrews on both sides of the SIP.
5.
Connect all cables to each SPA.
Cisco ASR 1000 Series Router Hardware Installation Guide
536
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing the Cisco ASR 1000 SPA Interface Processor

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g