Cisco ASR 1002 Hardware Installation Guide

Replacing the DC Power Supply in Cisco ASR 1013 Router
The color coding of the DC input power supply leads depends on the color coding of the DC power source
at your site. Typically, green or green/yellow is used for ground (GND), black is used for –48 V on negative
(–) terminal and red is used for RTN on the positive (+) terminal. Make certain the lead color coding you
choose for the DC input power supply matches lead color coding used at the DC power source.
Note
When you install the unit, the ground connection must always be made first and disconnected last. Statement
1046
Warning
To install the DC power supply, follow these steps:
SUMMARY STEPS
1.
Grasp the DC power supply by the two handles and carefully slide it into the chassis. Make sure you align
the rear connector to the backplane until it is fully seated.
2.
Tighten the captive screws on the power supply.
3.
Make certain that the chassis ground is connected before you begin installing the DC power supply.
4.
Locate the ground stud on the DC power supply for the GND connection which must be installed first and
follow these steps:
5.
Attach the other end of the ground cable to the site ground associated to the DC power supply system that
you are working on.
6.
Remove the plastic cover from the terminal block if it is still on.
7.
You must wrap the positive and negative power cables with sleeving. Take each wire and cover the area
from the lug to the wire with heavy shrink sleeving as pointed out in callout 3 (see xref fig).
8.
For easier cable-management, insert the positive cable first. Replace the ground lug with cable in the
following order as shown in:
9.
Tighten the Kepnut screw (use the screwdriver to tighten the ground screw in the terminal block to a torque
of 20+/–2 in-lbs / 2 per.) and repeat the same steps for the negative wires.
10.
Use tie wraps to secure the wires, so that the wires are not pulled from the terminal block by casual contact.
Ti-wrap studs are located below the power supply terminal block.
11.
Replace the terminal block plastic cover, which is slotted and keyed to fit correctly over the terminal block;
then tighten the black screw (use the screwdriver to tighten the screw to a torque of 5 in-lbs / 1 per.).
12.
Remove the tape from the circuit-breaker On/Off switch (if there was any).
13.
Switch the circuit breaker On/Off switch to the On (|) position.
Cisco ASR 1000 Series Router Hardware Installation Guide
595
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing and Replacing a DC Power Supply in Cisco ASR 1013 Router

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g