EasyManuals Logo
Home>Cisco>Network Router>ASR 1002

Cisco ASR 1002 Hardware Installation Guide

Cisco ASR 1002
702 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #694 background imageLoading...
Page #694 background image
What to Do Next
This completes the steps for recovering or replacing a lost enable, enable secret, or console login password.
Recovering the Password When a Standby RP Is Included in the System
If a standby RP is included in the system, perform the following procedure to recover the password:
You need not perform the password recovery procedure on the standby RP. After you bypass the NVRAM
(startup-config) on the active RP, subsequent reloads of the standby RP synchronize the running-config
of the standby RP with the running-config of the active RP.
Note
1
Connect to the console port of the standby RP. It is recommended that you create a console port connection
to the standby RP and not use the console port of the active RP.
2
Reset both RPs to the ROMmon prompt. See the xref
t_Details_of_the_Password_Recovery_Procedure_1043916.xml for information about the procedure.
Do not reboot the standby RP at this point. Leave it at the ROMmon prompt.
1
Perform the password recovery procedure on the active RP. See the xref
t_Details_of_the_Password_Recovery_Procedure_1043916.xml for information about the procedure.
2
After the running-config of the active RP has been modified with the password removed from the
running-config, save the new running-config to NVRAM (that is, copy the contents of the running-config
to the startup-config).
3
Start the standby RP.
The standby RP synchronizes its configuration with that of the active RP. The new configuration does not
include a password.
Cisco ASR 1000 Series Router Hardware Installation Guide
660
Troubleshooting Initial Startup Problems
Recovering the Password When a Standby RP Is Included in the System

Table of Contents

Other manuals for Cisco ASR 1002

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco ASR 1002 and is the answer not in the manual?

Cisco ASR 1002 Specifications

General IconGeneral
Ethernet LANYes
Cabling technology10/100/1000Base-T(X)
Networking standardsIEEE 802.3
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet interface typeGigabit Ethernet
DHCP client-
Supported network protocolsBGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports4
Security algorithmsSSH
VPN tunnels quantity8000
SafetyUL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
CertificationFCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory4096 MB
AC input voltage85 - 264 V
Power source typeAC
AC input frequency50 - 60 Hz
Power consumption (typical)560 W
Operating altitude0 - 3048 m
Storage temperature (T-T)0 - 50 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)5 - 95 %
Operating relative humidity (H-H)5 - 90 %
Product colorGray
Rack capacity2U
Weight and Dimensions IconWeight and Dimensions
Depth461 mm
Width437.4 mm
Height89 mm
Weight- g

Related product manuals