Cisco ASR 1002 Hardware Installation Guide

Image to Upgrade Field-Programmable Hardware Devices
Starting in Cisco IOS XE Release 3.1S, an independent image used to upgrade field programmable hardware
devices is released periodically, separate from the consolidated packages. An image is provided for the field
programmable device to customers in cases where a field upgrade is required. If the Cisco ASR 1000 Series
Router contains an earlier released version of the hardware programmable firmware on the Cisco ASR1000-RP,
Cisco ASR1000-SIP, or Cisco ASR 1000-ESP, then that hardware programmable firmware may need to be
upgraded.
Generally an upgrade is only necessary in cases where a system message indicates one of the field programmable
devices on the Cisco ASR 1000 Series Routers needs an upgrade or a Cisco technical support representative
suggests an upgrade.
For example, in Cisco IOS XE Release 3.1S, a hardware (hw)-programmable upgrade package file image that
contains a new version of the Complex Programmable Logic Device (CPLD) code is available for users who
need to update prior released Cisco ASR1000-RP2 and Cisco ASR1000-SIP10 modules in the Cisco ASR
1013 Router.
For information on performing a field programmable hardware device upgrade in the field, see Upgrading
Field Programmable Hardware Devices for Cisco ASR 1000 Series Routers .
Cisco ASR 1000 Series Route Processor
The Cisco ASR 1000 Series route processor is the central network clocking card and runs the network operating
system, BINOS kernel plus IOSD (IOS daemon). The Cisco ASR1000-RP1 and Cisco ASR1000-RP2 are
responsible for:
•
Selection of the active Cisco ASR 1000 Series Route Processor and the Cisco ASR 1000 Series Embedded
Services Processor and notification of the Cisco ASR 1000 Series SPA Interface Processor of these
events.
•
All the control processors communicating and performing packet processing on packets punted to it by
the Cisco ASR 1000 Series Embedded Services Processors.
The Cisco ASR 1000-RP1 and Cisco ASR1000-RP2 have LED status indicators, an RJ-45 plug for DTI and
BITS timing reference, and two USB ports which can be used with smart cards for secure key distribution.
Specific system tasks performed by the Cisco ASR 1000 Series Route Processors include the following:
•
Runs the router control plane, including network control packets, and connection setup
•
Supports single-bit error correction and multi-bit error detection
•
User interfaces: 10/100/1000 Mbps Management Ethernet, CON/AUX, USB
•
Active and standby ASR1000-RP1, ASR1000-RP2, and Cisco ASR 1000 Series Embedded Services
Processor master and standby synchronization (Tasks include switchover from failing master to standby.)
•
Code storage, management, and upgrade.
•
Supports on-board failure logging (OBFL) with 2 MB of memory.
•
Downloading operational code for SIPs and Cisco ASR 1000 Series Embedded Services Processor over
Ethernet out of band channel (EOBC), which is used for communication between the control processors
on the Cisco ASR 1000 Series Routers
Cisco ASR 1000 Series Router Hardware Installation Guide
36
Cisco ASR 1000 Series Routers Component Overview
Cisco ASR 1000 Series Route Processor

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g