Cisco ASR 1002 Hardware Installation Guide

ResultASR1000-SIPASR1000-ESPASR1000-RPRouter
——
Integrated
embedded services
processor
—
Cisco ASR 1001
Router
SIP-40 disabled
———
The following may be the outcome when using unsupported Cisco ASR 1000 components in a high-availability
feature configuration:
• Unsupported ASR1000-RP in a redundant Cisco ASR 1006 configuration—If you insert an Cisco
ASR1000-RP1 or RP2 in an ASR 1006 redundant setup, the following occurs:
The standby ASR1000-RP card is disabled and this error message prints on the active RP console:
Error message: %CMRP-3-RP_MISMATCH: [chars] has been held in reset because the part number
differs from that of the active RP.
rp_fru: R0/R1
Reason: The part number read from the FRU IDPROM is not compatible with part number of the active
ASR1000-RP; as a result it may not act as a standby.
Recommended action: Remove the FRU from the chassis
• Unsupported Cisco ASR 1000 series router power supply—If you insert the Cisco ASR 1013 router
power supply into the Cisco ASR 1006 Router or insert the Cisco ASR 1006 Router power supply into
the Cisco ASR 1013 Router, the following occurs:
The following error message displays when detected and then periodically after that (every 1 hour) until the
problem is corrected.
Error message: %CMRP-3-UNSUPPORTED_PEM: [chars] in slot [chars] is not supported with [chars]
and it needs to be replaced immediately
pem_name: ASR1006-PWR-AC/ASR1006-PWR-DC/ASR1013-PWR-AC/ASR1013-PWR-DC
pem_slot_num: P0-P3
hw_config: ASR-1006/ASR-1013 chassis
Reason: The Product ID read from the PEM IDPROM is not supported in this hardware configuration. It will
be allowed to continue but immediate replacement is required.
Recommended action: Remove the PEM from the chassis and replace it with a supported PEM.
If the above combinations occur, you will see the following error messages.
Unsupported ASR1000-ESP Error Message
This section describes what happens when a Cisco ASR1000-ESP40 is present when the router is booting or
inserted at a later time into the Cisco ASR 1000 Router and provides the error message and explanation as to
why this occurred.
Error message
The ASR1000-ESP40 card is disabled and the following error message displays at the console.
Error message
%CMRP-3-UNSUPPORTED_FRU: [chars] in slot [chars] is not supported with [chars] and so it
Cisco ASR 1000 Series Router Hardware Installation Guide
32
Cisco ASR 1000 Series Routers Component Overview
Cisco ASR 1000 Series Hardware Configuration Combinations

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g