Cisco ASR 1002 Hardware Installation Guide

Cisco ASR 1002-X
Router
Cisco ASR 1001
Router
Cisco ASR 1002
Router and Cisco
ASR 1002-F
Router
Cisco ASR 1004
Router
Cisco ASR 1006
Router
Cisco ASR 1013
Router
Hardware
Component
Not applicableNot applicableNot compatibleSupportedSupportedNot supportedASR1000-ESP20
Not applicableNot applicableNot compatibleSupportedSupportedSupportedASR1000-ESP40
Not applicableNot applicableNot compatibleNot compatibleSupportedSupportedASR1000-ESP100
Not compatibleNot compatibleNot compatibleNot compatibleNot compatibleSupportedASR1000-ESP200
Not applicableNot applicableNot applicableSupportedSupportedNot compatibleASR1000-RP1
Not applicableNot applicableNot applicableSupportedSupportedSupportedASR1000-RP2
Not applicableNot applicableNot applicableSupportedSupportedSupportedASR1000-SIP10
Not applicableNot applicableNot applicableSupportedSupportedSupportedASR1000-SIP40
ASR 1002 PEM
supported
Supported with
its own AC and
DC power
supplies
ASR 1002 PEM
supported
ASR1004 PEM
supported
ASR 1013 PEM
supported
ASR 1006 PEM
supported
ASR 1013 PEM
supported
ASR1000 PEMs
The following is the outcome of upgrades performed using incompatible combinations of hardware components:
•
The embedded services processor card is disabled and an error message is generated in either of the
following scenarios:
◦
Cisco ASR1000-ESP20, Cisco ASR1000-ESP40, or Cisco ASR1000-ESP100 is inserted in the
Cisco ASR 1002 Router.
◦
Cisco ASR1000-ESP5 is inserted into Cisco ASR 1004 Router, Cisco ASR 1006 Router, or Cisco
ASR 1013 Router.
•
The Complex Programmable Logic Device (CPLD) field programmable upgrade for Cisco
ASR1000-SIP10 cannot be performed in slot 5. Cisco ASR1000-SIP10 can be upgraded only in any one
of the slots from slots 0 to 4.
•
If Cisco ASR1000-RP1 is inserted into Cisco ASR 1013 Router, the card is disabled and an error message
is generated
The Cisco ASR 1013 Router supports only the following components:
•
Cisco ASR1000-RP2
•
Cisco ASR1000-ESP40 or Cisco ASR1000-ESP200
•
Cisco ASR1000-SIP10 or Cisco ASR1000-SIP40
Cisco ASR 1000 Series Router Hardware Installation Guide
6
Cisco ASR 1000 Series Routers Hardware Overview
Hardware Compatibility

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g