Cisco ASR 1002 Hardware Installation Guide

SUMMARY STEPS
1.
Remove the standby RP by performing the procedure described in the xref “Removing the Cisco ASR
1000 Series Route Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers”
section.
2.
Remove the DIMM memory module from the standby RP by performing one of the following procedures:
•
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
3.
Insert the new DIMM memory module on the standby RP by performing one of the following procedures:
•
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
4.
Insert the standby RP by performing the procedure described in the xref “Removing the Cisco ASR 1000
Series Route Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers” section.
5.
Verify the memory upgrade on the standby RP by running the following commands:
6.
Use the redundancy force-switchover command to switch the upgraded standby RP to the active state.
The RP that was in the active state moves to the standby state.
7.
Repeat Step 1 through Step 5 on the standby RP.
DETAILED STEPS
Step 1
Remove the standby RP by performing the procedure described in the xref “Removing the Cisco ASR 1000 Series Route
Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers” section.
Step 2
Remove the DIMM memory module from the standby RP by performing one of the following procedures:
•
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
Step 3
Insert the new DIMM memory module on the standby RP by performing one of the following procedures:
•
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
Step 4
Insert the standby RP by performing the procedure described in the xref “Removing the Cisco ASR 1000 Series Route
Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers” section.
Step 5
Verify the memory upgrade on the standby RP by running the following commands:
Example:
Router# configure terminal
Router(config-red)# redundancy
Router(config-r-mc)# main-cpu
Router(config-r-mc)# standby console enable
Router(config-r-mc)# end
Router-stby# show version
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Experimental Version
Cisco ASR 1000 Series Router Hardware Installation Guide
496
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing and Replacing the DIMM Memory Modules on the Cisco ASR 1006 Router and the Cisco ASR 1013 Router

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g