Cisco ASR 1002 Hardware Installation Guide

Table 90: Cisco ASR1000-RP1 Supported Slots for Inserting Memory DIMMs
Slot 1Slot 0Memory PID Option
2 GB module2 GB moduleM-ASR1K-RP1-4GB=
1GB module1 GB moduleM-ASR1K-RP1-2GB=
Perform the following steps before you begin:
•
Use an ESD-preventive wrist strap
•
Back up data before replacing a eUSB device.
•
The card is keyed and slotted for easier connection.
•
Never wiggle the DIMM.
•
Handle the connector according to the instructions (see xref Figure 14-15).
To replace or upgrade the Cisco ASR1000-RP1 DIMM memory spare, follow these steps:
SUMMARY STEPS
1.
Attach an ESD-preventive wrist strap between you and an unpainted router surface.
2.
Locate the DIMM on the system board.
3.
Press both spring latches outward to release the DIMM.
4.
Pull the latches away from the DIMM on both edges. This lifts the DIMM slightly. Gently lift the DIMM
free from the DIMM connector, taking care not to touch the pins that insert into the socket.
5.
Place the DIMM in an antistatic bag to protect the DIMM from ESD damage.
6.
To install the DIMM memory card, locate the notches and align the DIMM with the socket before inserting
it.
7.
Make certain that both latches on the DIMM connector are open.
8.
Gently insert the new DIMM, taking care not to damage the pins on the edge of the DIMM.Using two
hands, place the index fingers on the edge of the DIMM and place the thumbs on the socket, being careful
not to touch the socket pins. Press on the back of the DIMM towards the socket by squeezing the index
fingers and the thumbs together, being careful to only apply force onto the DIMM parallel with the plane
of the DIMM.
9.
To allow the DIMM to slide into the socket smoothly with minimum force, one can alternate applying
force back and forth between the left hand and the right hand, allowing one side to engage prior to the
other. Carefully and firmly press the DIMM into the connector until the spring latches lock the DIMM in
place. See Figure 14-12.
10.
Slide the DIMM one side at a time. Use light insertion force and insert smoothly; but make certain the
DIMM is inserted straight .
Cisco ASR 1000 Series Router Hardware Installation Guide
498
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g