Cisco ASR 1002 Hardware Installation Guide

DETAILED STEPS
Step 1
Attach an ASCII terminal to the console port on your router.
Step 2
Configure the terminal to operate at 9600 baud, 8 data bits, no parity, and 1 stop bit (9600 8N1).
Step 3
If you can log in to the router as a nonprivileged user, enter the show version command to display the existing configuration
register value. Note the value for use later and proceed to Step 6. If you cannot log in to the router at all, go to the next
step.
Step 4
Press the Break key or send a Break from the console terminal. If Break is enabled, the router enters the ROM monitor,
indicated by the ROM monitor prompt (rommon1>). Proceed to Step 6. If Break is disabled, power cycle the router (turn
the router off or unplug the power cord, and then restore power after waiting 30 seconds). Then proceed to Step 5.
Step 5
Within 60 seconds of restoring the power to the router, press the Break key or send a Break. This action causes the router
to enter the ROM monitor and display the ROM monitor prompt (rommon1>).
Step 6
Set the configuration register using the configuration register utility; enter the confreg command at the ROM monitor
prompt as follows:
Example:
rommon1> confreg
Step 7
Answer yes to the enable ignore system config info? question, and note the current configuration register settings.
Step 8
Initialize the router by entering the reset command as follows:
Example:
rommon2> reset
The router initializes, the configuration register is set to 0x142, and the router boots the system image from flash memory
and enters the System Configuration Dialog prompt as follows:
Example:
--- System Configuration Dialog --
Step 9
Enter no in response to the System Configuration Dialog prompts until the following message is displayed:
Press RETURN to get started!
Step 10
Press Return. The user EXEC prompt is displayed as follows:
Router>
Step 11
Enter the enable command to enter privileged EXEC mode. Then enter the show startup-config command to display the
passwords in the configuration file as follows:
Router# show startup-config
Step 12
Scan the configuration file display looking for the passwords (the enable passwords are usually near the beginning of
the file, and the console login or user EXEC password is near the end). The passwords displayed look something like
this:
enable secret 5 $1$ORPP$s9syZt4uKn3SnpuLDrhuei
enable password 23skiddoo
.
.
Cisco ASR 1000 Series Router Hardware Installation Guide
658
Troubleshooting Initial Startup Problems
Details of the Password Recovery Procedure

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g