Korg Oasys - Page 140

Sampling (Open Sampling System)
132
5. Select“Index.”
Youcanalsoselect“Index”byholdingdownthe
ENTERswitchandplayingapadoranoteonthe
keyboard.Forthisexample,select001.
6. Assignasampletothe“Index.”
IfRAMmemoryalreadycontainssamples,use
“SampleSelect”toselectthesampleandassignit.
Ifyouwant
torecordanewsample,youcansample
itnow.
Thesampleyourecordwillbeautomatically
assignedtotheindexyouselectedinstep4.
Theassignedsamplewillsoundwhenyouplaythe
keyboardintherangeoftheindextowhichthe
sampleisassigned.
7. Repeatsteps5
and6toassignasampletoeach
index.
Thenumberandorderoftheindexesina
multisample,therangeofeachindex,andthe
originalkeypositioncanbefreelychangedlaterif
desired.(See“Multisampleediting”onp.142)
Creating multiple samples
Intheexampleproceduredescribedabove,several
indexeswerecreated(bypressingtheCreatebutton
severaltimes),andthensampleswereassignedtoeach
“Index.”
Asanalternativemethod,itisalsopossibletocreate
oneindex,sampleintoit,andthenrepeatthesetwo
steps.
1. PresstheCreatebuttononceto
createanindex.
2. Recordasample.
Therecordedsamplewillautomaticallybeassigned
totheindexyoucreatedinstep1.
3. Repeatsteps1and2.
Thisisanefficientwaytorecordmultiplesamples.
Assigning samples to the pads
Bydefault,pads1–8correspondtotheC2–G2keys.
Forexample,thedefault“Index”settingfor001/008
sets“OrigKey”and“TopKey”toC2.Theassigned
samplewillsoundwhenyouplaytheC2key.The
samesamplewillalsosoundwhenyoustrikepad1.
Similarly,ifyouassignsamplesto
“Index”002–008,the
samplesthatsoundwhenyouplaytheC#2–G2keys
willalsosoundwhenyoustrikepads2–8.
IfyoupressthePADMODEswitchtomake
VELOCITYSENSITIVElight,youwillbeableto
changethevolumebyadjustingtheforcewithwhich
youstrikethepads.If
youmakeFIXEDVELOCITY
light,thevolumewillbeaccordingtothevelocity
valuesspecifiedintheSamplingP4:EQ/Controller–
PadsSetuppage.
Foreachpad,youcanchangethenotenumbersused
toplaysamples.
ThesesettingsaremadeintheSamplingP4:
EQ/Controller–PadsSetuppage.Forexample,you
mightassigntheinfrequently‐playedhighesteight
notesofthe76‐notekeyboard(C7–G7)tocorrespond
tothepads.Tomakethesetting,selectthenotenumber
field,andplaythedesiredkeywhileholdingdownthe
ENTERswitch.
Basic examples of sampling
Sampling your voice from a mic, and
playing it back as a one-shot sample
Inthisexamplewewilluseamicconnectedtothe
AUDIOINPUT1jacktosampleyourvoicein
monaural.
Connect a mic
1. ConnectamictotherearpanelAUDIOINPUT1
jack.
PresstheAUDIOINPUTMIC/LINEswitchsothat
it’sintheMIC(outward)position,andsetthe
LEVELknobnearthecenter.Ifyou’ reusinga
phantom‐poweredcondensermic,turnthe
PHANTOMswitchon.(See“A u d i o inputsettings”
on
page 125)
2. AccesstheSamplingP0:Recording–AudioInput
page.
PresstheMODESAMPLINGswitchtoenter
Samplingmode.MakesurethattheSamplingP0:
Recordingpageisdisplayed.
Ifitisnot,presstheEXITswitch,andthenpressthe
AudioInputtab.
3. IntheP0:Recording–AudioInputpage,makethe
followingsettings.
–INPUT1–
BusSelect(IFX/Indiv.)L/R
Pan:L000
Level:127
ThisspecifiestheinputlevelandpanoftheINPUT
1jack,andassignsL/Rbusasthedestination.
Condenser
mic
ON MIC