Korg Oasys - Page 179

Saving data Writing to internal memory
171
CombinationP0:Play–ProgSelect/Mixer
“Category”(Category/ProgramSelect)
SequencerP0:Play/REC–MIDITrackProgSelect/
Mixer“Category”(Category/ProgramSelect)
6. Use“To”tospecifythebankandnumberofthe
writingdestinationprogram/combination.
UsetheVALUEcontrollersortheBANKswitchesto
makeyourselection.
7. ToexecutetheWriteoperation,presstheOK
button.
Tocancelwithoutexecutingpressthe
Cancelbutton.
WhenyoupresstheOKbutton,thedisplaywillask
“A r e yousure?”WhenyoupresstheOKbuttononce
again,thedatawillbewritten.
Using the (SEQUENCER) REC/WRITE
switch to write
Thismethodcanonlybeusedtowritetheselected
program/combinationnumber.
1. PresstheSEQUENCERREC/WRITEswitch.
ThefollowingUpdateProgram/Update
Combinationdialogboxwillappear.
ThescreenshownisforProgrammode
2. Towritethedata,presstheOKbutton.Tocancel
withoutwriting,presstheCancelbutton.
Writing Drum Kits and Wave Sequences
Here’showadrumkitorwavesequenceyou’veedited
inGlobalmodecanbewrittenintotheinternal
memoryoftheOASYS.
TheWaveSequence“Tempo,”“KeySync,”
“Swing,”and“QuantizeTrigger ”settingsarestored
witheachprogram,combination,orsong.These
parametersarenotsavedbywritingthewave
sequenceasdescribedhere.Ifyou’vemovedfrom
ProgramorCombinationmodeandeditedthese
parameters,returntothepreviousmodeandwrite
youredits.
Using the page menu Write command
1. Pressthepagemenubutton,andpress“Write
DrumKit”or“WriteWaveSequence”inthe
menu.
TheWriteDrumKit/WriteWaveSequencedialogbox
willappear.
Note:Youcangetthesamedialogboxbyholding
downtheENTERswitchandpressingthe0switch.
(See“Shortcuts”onpage 27)
Thescreen
shownisforDrumKit
2. Verifythenameofthewrite‐sourcedrumkitor
wavesequenceshownintheupperline.
3. Ifyouwanttoeditthenameofthedrumkitor
wavesequence,pressthetexteditbutton.
Thetexteditdialogboxwillappear.Inputthedesired
name
forthedrumkitorwavesequence.(See“Editing
names”onpage 172)
Whenyou’veinputthename,presstheOKbuttonto
returntotheWriteDrumKit/WriteWaveSequence
dialogbox.
4. Usethe“To”fieldtospecifythebankandnumber
ofthewrite‐destinationdrumkitorwave
sequence.
Use
theVALUEcontrollerorBANKswitchestospecify
thedesiredsetting.
5. Towritethedata,presstheOKbutton.Ifyou
decidenottowrite,presstheCancelbutton.
WhenyoupresstheOKbutton,thedisplaywillask
“A r e yousure?”PresstheOKbuttononceagainto
writethedata.
Using the (SEQUENCER) REC/WRITE
switch to write
Youcanusethismethodtowritetheselecteddrumkit
orwavesequence.
1. PresstheSEQUENCERREC/WRITEswitch.
TheUpdateDrumKit/UpdateWaveSequence
dialogboxwillappear.
ThescreenshownisforDrumKit
2. Towritethedata,presstheOKbutton.Ifyou
decidenottowrite,presstheCancel
button.
About the Edit Buffer
Whenyouselectaprogram,combination,wave
sequence,ordrumkitinProgramP0:Play,
CombinationP0:Play,GlobalP4:WaveSequencer,or
GlobalP5:DrumKitrespectively,thedataiscalledinto
theeditbufferoftheOASYS.
WhenyouthenusethevariousProgramor
CombinationpagesorGlobal
modeP4/P5pagestoedit
theparameters,yourchangeswillaffectthedatainthe
editbuffer.