Index-13
Reverse Direction input 4-33
RFI 2-3
RGOK FAILED TO ACTIVATE 5-28
RGOK FAILED TO DEACTIVATE 5-28
RGS 4-33
RGSR 4-33
RINAX 4-33
Rope gripper reset 2-14
Rope slip (traction loss) fault 3-39
RSTDRV 4-41
Run Tests 3-19
Run the motor 2-20, 2-25
RUN, Run flag 4-10
RUN/A/B 4-33
S
S = Slave 4-6
S in upper left corner of LCD 5-38
SAB, Sabbath input flag 4-10
SAB, Sabbath Operation Input option 4-33
SABBATH OPERATION 4-46
Sabbath Operation 4-46
SABBATH OPERATION ACTIVE 5-36
Sabbath Operation Input 4-33
SAF 4-10
SAFC 4-33
SAFC INPUT FAILURE 5-36
SAFETY CIRCUIT IS OPEN 5-36
SAFETY DROPPED BY SPB 5-36
SAFH 4-33
SAFO 4-41
Saving Changes 4-11
SC-3HN 1-8
SC-3HN board 5-72
SCE, Stepping correction enable flag 4-10
Schematic symbols, description of 2-5
SCROLLING SPEED 4-47
SCROLLING SPEED option 4-48
SD, Supervisory down flag 4-10
SDA, Down direction arrow flag 4-10
SDT, Short door time flag 4-10
SDTR, Short door time flag (rear) 4-10
SE, Safety edge input flag 4-10
SEC, Security Code Incorrect output option 4-41
SECONDARY PARKING FLOOR option 4-15
Security Code Incorrect 4-41
Seismic equipment install 2-53
Selective Collective 4-13
SEQUENTIAL DOOR OPER. (F/R) option 4-18
SER, Safety edge input (rear) flag 4-10
Serial car panel CAN data 4-111
Serial car panel option 1-3
Serial hall call 1-3
Serial Hall Call Node Board 5-72
SerSP 2-32, A-2
set parameters to default values 4-5
Sheave Brake Idle Delay, 190 4-139
Shorts 2-9
Signal operating mode 2-32, A-2
SIMP, Simplex Input option 4-33
Simplex Input 4-33
SIMPLEX OR DUPLEX option 4-13
Simplex Output 4-41
SIMPO, Simplex Output option 4-41
Sin/Cos 2-23
Single Automatic Push button 4-13
Single Button Collective 4-13
SINGLE SPEED AC OPTION 4-46
Slew Filter 4-134
SLV, Stable slave flag 4-10
Smoothing tape edges 2-57
Software version
CHP 4-143
CTLA 4-143
CTLB 4-143
CTLC 4-143
MPIA 4-143
MPIB 4-143
MPIC 4-143
MPUA 4-143
UIO 4-143
SPA (Safety Processor A) 5-76
SPA IS OFFLINE 5-30, 5-37
SPARE OUTPUTS MENU OPTIONS 4-35
SPB (Safety Processor B) 5-76
SPB IS OFFLINE 5-21, 5-37
SPC IS OFFLINE 5-28, 5-37
Specifications 1-2
SPEED 0 FPM 4-55
Speed and Acceleration Control 2-30
Speed Changes Felt Excessively in Car 3-19
Speed Drop Delay, 192 4-139
Speed Hysteresis Delay 4-133
Speed Hysteresis Delay, 139 4-134
Speed Pick Delay Time 4-133
SST, Soft stop timer flag flag 4-9
Standard Acceleration 4-136
Standard Curve 3-12
Standard Deceleration 4-137
Standard Roll Jerk 4-136
Standard Slew Slope 4-134
Standard Start Jerk 4-136
Standard Stop Jerk 4-136
Start Input 4-33
Start jerk 3-13
STARTIN, Start Input option 4-33
STDX 4-33
Steel tape 2-57
Stick alignment 2-61
STOP 4-33
Stop SW 5-15
STUCK PHOTO EYE PROTECTION option 4-18
STUX 4-33
SU, Supervisory up flag 4-10
SUA, Up direction arrow flag 4-10
Subnet mask screen 4-112
SWG 4-33
System CAN Bus 4-111
To Next Page
Loading...