YASKAWA AC Drive-A1000

Installing Peripheral Devices.................................................. 366
Installing the Cooling Fan ..................................................... 354
Integral Limit Setting........................................................... 144
Integral Operation during Accel/Decel ...................................... 164
Integral Operation during Accel/Decel for Motor 2........................ 165
Integral Time Setting (I) ....................................................... 144
Interlock Circuit Example .......................................................73
Internal Dynamic Braking Resistor Protection Selection (ERF type)...263,
433
Inversion Detection............................................................. 303
Inversion Prevention Detection ............................................... 303
IP00/Open-Chassis ...............................................................34
IP20/NEMA Type 1 ..............................................................34
J
Jog Frequency Reference ...................................................... 169
Jump Frequency........................................................... 172, 294
Jump Frequency Width ........................................................ 172
K
KEB Acceleration Time ................................................. 249, 428
KEB Deceleration Time ................................................. 249, 428
KEB Detection Time ........................................................... 249
KEB Function Related Adjustments ......................................... 247
KEB Method Selection......................................................... 249
KEB Operation Using a KEB Input .......................................... 244
KEB Operation Using L2-02, Without KEB Input......................... 245
KEB Operation Using L2-02 and KEB Input............................... 245
KEB Operation Using L2-10, Without KEB Input......................... 246
KEB Operation Using L2-10 and KEB Input............................... 246
KEB Operation Wiring Example ............................................. 247
KEB Ride-Thru End Detection ............................................... 245
KEB Ride-Thru Function...................................................... 215
KEB Ride-Thru Start........................................................... 244
KEB Start Output Frequency Reduction..................................... 428
Keys and Displays on the Digital Operator ...................................79
kWh............................................................................... 452
kWh, Lower 4 Digits ........................................................... 452
kWh, Upper 5 Digits ........................................................... 452
kWh Monitor Initialization .................................................... 283
kWh Monitor Initial Value Selection ........................................ 442
L
L3-01 through L3-06 ........................................................... 294
L3-02 ....................................................................... 340, 342
L3-04 ............................................................................. 340
L3-06 ............................................................................. 340
L3-11 ............................................................................. 294
L5-01 ............................................................................. 322
L6-02 ............................................................................. 321
L6-02 and L6-03 ................................................................ 322
L6-03 ............................................................................. 321
L6-05 ............................................................................. 321
L6-05 and L6-06 .......................................................... 321, 323
L6-06 ............................................................................. 321
L7-01 ............................................................................. 330
L7-01 through L7-04 ..................................................... 294, 341
L7-02 ............................................................................. 330
L7-06 ............................................................................. 294
L7-07 ............................................................................. 294
L8-02 ............................................................................. 320
L8-12
............................................................................. 377
L8-29 ............................................................................. 377
L8-38 ............................................................................. 342
Language Selection............................................................. 120
LCD Display ......................................................................80
Leakage Inductance Alarm .................................................... 328
Leakage Inductance Error ..................................................... 330
LED Check ...................................................................... 452
LED Operator ................................................................... 361
LF ................................................................................. 305
LF2 ............................................................................... 305
Line Driver PG.................................................................. 361
Line-to-Line Motor Resistance Online Tuning ............................. 438
Line-to-Line Resistance Error................................................. 329
LO/RE................................................................... 81, 89, 112
LO/RE (LOCAL/REMOTE) Key Function Selection..................... 132
LO/RE LED .......................................................................81
LO/RE Light.......................................................................79
LO/RE Selection Key ............................................................79
Load Current .................................................................... 438
Load Inertia................................................................ 277, 439
Load Inertia Ratio................................................... 165, 255, 430
LOCAL.............................................................................89
LOCAL/REMOTE Key Function Selection ................................ 440
LOCAL/REMOTE Run Selection............................................ 132
Loopback Test................................................................... 475
Loss of Reference Function ................................................... 257
Low Voltage Wiring for Control Circuit Terminals ....................... 499
LT-1 .............................................................................. 319
LT-2 .............................................................................. 320
LT-3 .............................................................................. 320
LT-4 .............................................................................. 320
M
M1 ..................................................................................62
M2 ..................................................................................62
M3 ..................................................................................62
M4 ..................................................................................62
M5 ..................................................................................62
M6 ..................................................................................62
MA..................................................................................62
Magnetic Flux Compensation Value ......................................... 134
Main Circuit Connection Diagram ........................................ 53, 60
Main Circuit Terminal ...........................................................36
Main Circuit Terminal and Motor Wiring.....................................59
Main Circuit Terminal Block Configuration..................................54
Main Circuit Terminal Functions...............................................58
Main Circuit Terminal Wiring ..................................................36
Main Circuit Wiring..............................................................58
Main Power Circuit Voltage Adjustment Gain ............................. 429
Maintenance ............................................................... 225, 352
Maintenance Alarms ........................................................... 352
Maintenance Monitors ......................................................... 284
Maintenance Monitor Settings ................................................ 282
Master Speed Reference Lower Limit ....................................... 172
Maximum Applicable Motor Capacity ...................................... 373
Maximum Output Frequency............................................ 186, 373
Maximum Output Voltage..................................................... 373
Maximum Voltage.............................................................. 186
MB..................................................................................62
Index
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual
523