YASKAWA AC Drive-A1000 User Manual

MC..................................................................................62
Mechanical Weakening Detection............................................ 225
Mechanical Weakening Detection 1 ................................... 310, 321
Mechanical Weakening Detection 2 ......................................... 314
Mechanical Weakening Detection Operation ......................... 260, 432
Mechanical Weakening Detection Speed Level ...................... 261, 432
Mechanical Weakening Detection Start Time ........................ 261, 432
Mechanical Weakening Detection Time............................... 261, 432
MECHATROLINK-II Parameters ........................................... 201
MEMOBUS/Modbus Comm. Test Mode Complete ....................... 322
MEMOBUS/Modbus Communication Error.......................... 300, 317
MEMOBUS/Modbus Communications Reference......................... 453
MEMOBUS/Modbus Communication Test Mode Error.................. 322
MEMOBUS/Modbus Data Table............................................. 477
MEMOBUS/Modbus Error Code ............................................ 449
MEMOBUS/Modbus Error Codes ........................................... 493
MEMOBUS/Modbus Setup Parameters ..................................... 468
MEMOBUS/Modbus Specifications ......................................... 465
MEMOBUS/Modbus Switch Settings .........................................71
MEMOBUS/Modbus Termination .............................................36
Menu Structure for Digital Operator ...........................................83
Message Format................................................................. 473
Middle Output Frequency ..................................................... 186
Middle Output Frequency 2 ................................................... 187
Middle Output Frequency Voltage ........................................... 187
Middle Output Frequency Voltage 2......................................... 187
Mid Output Voltage A ......................................................... 290
Minimum KEB Time........................................................... 249
Minimum Output Frequency .................................................. 187
Minimum Output Frequency Voltage........................................ 187
Minimum Output Voltage ..................................................... 290
Minimum Wait Time for Sending Messages................................ 472
Minor Alarms ................................................................... 296
Minor Fault ...................................................................... 329
Minor Fault and Alarm Displays ............................................. 297
Minor Faults ..................................................................... 296
Minor Faults and Alarms ................................................ 295, 296
Model, Voltage Class, Capacity Mismatch.................................. 333
Model Number and Nameplate Check .........................................32
Modes ..............................................................................84
Momentary Overcurrent Protection .......................................... 375
Momentary Power Loss Minimum Baseblock Time................. 248, 428
Momentary Power Loss Operation Selection ......................... 138, 427
Momentary Power Loss Ride-Thru .................................... 243, 375
Momentary Power Loss Ride-Thru Time ............................. 248, 427
Momentary Power Loss Voltage Recovery Ramp Time ............ 248, 428
Monitor Output....................................................................62
Monitor Parameters....................................................... 234, 448
Most Recent Fault .............................................................. 451
Motor 1/Motor 2 Selection .................................................... 106
Motor 1 Parameters............................................................. 187
Motor 2 ASR Gain Switching Frequency ................................... 165
Motor 2 ASR Integral Limit................................................... 165
Motor 2 ASR Integral Time ................................................... 165
Motor 2 ASR Limit............................................................. 165
Motor 2 ASR Primary Delay Time Constant ............................... 165
Motor 2 ASR Proportional Gain.............................................. 165
Motor 2 Base Frequency....................................................... 190
Motor 2 Base Voltage .......................................................... 190
Motor 2 Control Mode Selection ............................................. 190
Motor 2 Inertia
.................................................................. 166
Motor 2 Iron Loss............................................................... 192
Motor 2 Leakage Inductance .................................................. 192
Motor 2 Line-to-Line Resistance ............................................. 192
Motor 2 Load Inertia Ratio .................................................... 166
Motor 2 Max Output Frequency .............................................. 190
Motor 2 Max Voltage .......................................................... 190
Motor 2 Mechanical Loss...................................................... 192
Motor 2 Mid Output Frequency............................................... 190
Motor 2 Mid Output Frequency 2 ............................................ 190
Motor 2 Mid Output Frequency Voltage .................................... 190
Motor 2 Mid Output Frequency Voltage 2 .................................. 190
Motor 2 Minimum Output Frequency........................................ 190
Motor 2 Minimum Output Frequency Voltage ............................. 190
Motor 2 Motor Iron-Core Saturation Coefficient 1 ........................ 192
Motor 2 Motor Iron-Core Saturation Coefficient 2 ........................ 192
Motor 2 Motor Poles ........................................................... 192
Motor 2 Parameters............................................................. 191
Motor 2 Rated Current ......................................................... 191
Motor 2 Rated No-Load Current.............................................. 191
Motor 2 Rated Power........................................................... 193
Motor 2 Rated Slip ............................................................. 191
Motor 2 Slip Compensation Gain............................................. 158
Motor 2 Slip Compensation Limit............................................ 158
Motor 2 Slip Compensation Primary Delay Time.......................... 158
Motor 2 Slip Compensation Selection during Regeneration.............. 159
Motor 2 Torque Compensation Gain......................................... 160
Motor Acceleration Time...................................................... 273
Motor Acceleration Time for Inertia Calculations ................... 255, 430
Motor Base Frequency ............................................. 105, 107, 444
Motor Base Speed ........................................................ 107, 444
Motor Code Selection .......................................................... 193
Motor Data Error................................................................ 329
Motor d-Axis Current at Previous Fault ..................................... 451
Motor d-Axis Inductance ...................................................... 194
Motor Direction at Power Up when Using Operator................. 281, 441
Motor Direction Error.......................................................... 330
Motor Does Not Rotate ........................................................ 337
Motor Excitation Current (ld) ................................................. 454
Motor Hunting and Oscillation Control Parameters ....................... 294
Motor Induction Voltage Constant 1......................................... 194
Motor Induction Voltage Constant 2......................................... 195
Motor Inertia .............................................................. 111, 165
Motor Iron-Core Saturation Coefficient ..................................... 328
Motor Iron-Core Saturation Coefficient 1................................... 188
Motor Iron-Core Saturation Coefficient 2................................... 188
Motor Iron Loss........................................................... 108, 445
Motor Iron Loss for Torque Compensation ................................. 189
Motor is Too Hot ............................................................... 338
Motor Leakage Inductance .................................................... 188
Motor Line-to-Line Resistance ............................................... 188
Motor Mechanical Loss........................................................ 189
Motor No-Load Current.................................................. 107, 188
Motor Overheat ................................................................. 320
Motor Overheat Alarm (PTC Input).......................................... 309
Motor Overheat Alarm Operation Selection .......................... 242, 427
Motor Overheat Fault (PTC Input) ........................................... 309
Motor Overheat Fault Operation Selection............................ 242, 427
Motor Overload ................................................................. 309
Motor Overload Estimate (oL1) .............................................. 452
Index
524
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual

YASKAWA AC Drive-A1000 Specifications

General

Brand	YASKAWA
Model	AC Drive-A1000
Category	Controller
Language	English