Lenze 8400 - Page 1584

Index
1584 Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Multilingualism 37
N
Network management telegram (NMT) 713
NMT (network management) 713
Node address 709
Node ID 709
Number of CAN SDO channels (C00366) 883
Number of encoder increments (C00420) 891
O
oC1: Power section - short circuit (error message) 659
oC10: Maximum current reached (error message) 660
oC11: Clamp operation active (error message) 662
oC12: I2xt overload - brake resistor (error message) 662
oC13: Maximum current for Fch exceeded (error message) 663
oC14: Direct-axis current controller limitation (error message)
664
oC15: Cross current controller limitation (error message) 664
oC16: Torque controller limitation (error message) 664
oC17: Clamp sets pulse inhibit (error message) 660
oC18: Current monitoring overload (error message) 661
oC19: Brake resistor - short circuit (error message) 662
oC2: Power section - earth fault (error message) 660
oC5: Ixt overload (error message) 658
oC6: I2xt overload - motor (error message) 664
oC7 301
oC7: Motor overcurrent (error message) 658
oH1: Heatsink overtemperature (error message) 657
oH3: Motor temperature (X106) triggered (error message) 658
oH4: Heatsink temp. > shutdown temp. -5°C (error message)
657
Open-circuit monitoring - encoder 311
Operating conditions (CAN on board) 701
Operating mode
Homing
553
Manual jog 573
Position follower 598
Positioning 582
Speed follower 551
StandBy 513
Stop 597
Operating mode change with profile number 524
Operation at 120 % 262
Operation with increased rated power 262
Operation with safety module 514
Optical tracking 111
Optimising the response to setpoint changes (SC) 245
Optimising the response to setpoint changes (SLVC) 202
Option "Lock bFail at TroubleQSP" 129
Original application|control source (C00008) 815
oS1: Maximum speed limit reached (error message) 660
oS2: Max. motor speed (error message) 661
Oscillation damping 272
Oscillation damping filter time (C00235) 864
Oscillation damping influence (C00234) 864
Oscilloscope function 682
ot1: Maximum torque reached (error message) 658
ot2: Speed controller output limited (error message) 663
oU: DC bus overvoltage (error message) 659
Output frequency (C00058) 826
Overchange 588
Override 601
Override point of field weakening (C00080) 830
OxI
Current (C00437)
893
OxU
Voltage (C00436)
893
OxU/I
Gain (C00434)
892
Input value (C00439) 894
Offset (C00435) 893
P
Parameter change-over 789
Parameterisable function blocks 1194
Password data (C00505) 912
Password protection 43
PC manual control 89
PDO mapping 717, 719, 721, 723
PDO synchronisation 733
Peak current limitation 154
Phase controller 285
Phase sequence reversal 275
Plant parameters 140
PLI without motion
Adaptation of ident angle (C02875)
1154
Adaptation of time duration (C02872) 1153
Ident. el. rotor displ. angle (C02873) 1153
Optimisation factor (C02870) 1153
Running time (C02871) 1153
PLI without motion (C02874) 1154
Pole position identification 226
Port block "LP_CanIn1" 717
Port block "LP_CanIn2" 719
Port block "LP_CanIn3" 721
Port block "LP_CanIn4" 723
Port block "LP_CanOut1" 725
Port block "LP_CanOut2" 726
Port block "LP_CanOut3" 727
Port block "LP_CanOut4" 728
PosExecute (control bit) 523
PosExecute control bit 523
position control 285
Position controller
Limitation (C02556)
1133
Position encoder selection (C00490) 911
Position follower 598