Lenze 8400 - Index

Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23 1563
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Numbers
16-bit inputs (C00831) 982
16-bit inputs (Set2) (C00836) 994
16-bit inputs [%] (C00830) 980
16-bit inputs [%] (Set2) (C00835) 990
16-bit inputs [Incr./ms] (C00832) 984
16-bit inputs [Incr./ms] (Set2) (C00837) 997
16-bit inputs I/O level (C00841) 1010
16-bit inputs I/O level [%] (C00840) 1008
24 V supply voltage (C00065) 827
32-bit inputs [incr] (C00834) 990
32-bit inputs [incr] (Set2) (C00839) 1006
32-bit inputs I/O level [incr] (C00844) 1016
87-Hz operation 165
A
Accel. time - main setpoint (C00012) 818
Acceleration override 603
Access protection 42
Accessories for commissioning 33
ACDrive
Control word (C01351)
1094
Drive mode (C01350) 1094
Setpoint scaling (C01353) 1096
Status word (C01352) 1095
Acknowledgement error 748
Activating the bus terminating resistor 704
Active COBID (C00355) 880
Actual values (C00055) 825
Adapt keypad menus 36
Add. accel. time x (C00101) 834
Add. decel. time x (C00103) 835
Additive speed specification 285
AIN1
Characteristic (C00010)
817
AIN2
Characteristic (C00020)
820
AINx
Configuration (C00034)
823
Gain (C00027) 822
Input current (C00029) 822
Input voltage (C00028) 822
Offset (C00026) 821
Output value (C00033) 822
An01: AIN1_I < 4 mA (error message) 666
An02: AIN2_I < 4 mA (error message) 666
Analog terminals 347
For electrical data see the hardware manual
User-defined terminal assignment
365
Angle controller overflow 1365
Angle correction in case of transmission errors 1397
AOutx
Decoupling value (C00442)
895
Appl.
Reference frequency C11 (C00059)
826
Reference speed (C00011) 817
Application (C00005) 812
Application block "LA_NCtrl" 377, 406
Application block "LA_SwitchPos" 467
Application notes 26
Application units
Configuration of the display parameters
1534
Display factor (C00485) 909
Offset (C00484) 909
Text (C00486) 910
Application units (C00487) 910
Assignment of the process data objects 716
Auto-DCB 268
Hold time (C00106) 836
Threshold (C00019) 819
AutoFailReset configuration (C00188) 857
AutoFailReset function 643
AutoFailReset repetition time (C00184) 856
AutoFailReset residual runtime (C00185) 857
Automatic DC-injection braking (auto DCB) 268
Automatic motor data identification 141
Auto-start option 123
Auto-start option (C00142) 843
B
Basic drive functions 497
Basic functions 497
Behaviour after mains connection 123
Binary inputs (C00833) 987
Binary inputs (Set2) (C00838) 1001
Binary inputs I/O level (C00843) 1012
Binding ID 47
Bit error 748
Blocks 1243
Brake chopper 286
Master-slave operation 294
Brake control 605
Brake energy management (C00175) 854
Brake resistance value (C00129) 839
Brake resistor 286
Brake resistor monitoring (I2xt) 303
Brake resistor overload threshold (C00572) 920
Brake resistor utilisation (C00133) 840
Braking operation/brake energy management 286
Braking procedures 289
C
C1 809
C10 817
C100 834
C1000 1036
C1001 1037
C101 834, 1436
Index