Lenze 8400 - Page 1585

Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23 1585
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Position teaching 596
Positioning 582
Positioning modes 589
Power display (C00980) 1032
Power section ID (C00093) 833
Power-on time meter (C00179) 855
Pre-defined error field (I-1003) 757
Printing the interconnection 1237
Process data objects, identifiers 729
Processing time 703
Producer heartbeat time (I-1017) 761
Product type code (C00203) 860
Profile data
Acceleration (C01303)
1092
Deceleration (C01304) 1092
Final speed (C01305) 1092
Position (C01301) 1091
Positioning mode (C01300) 1090
Sequence profile (C01307) 1093
Speed (C01302) 1091
S-ramp time (C01306) 1093
TP profile (C01308) 1093
TP signal source (C01309) 1094
Profile generator (L_DFRFG) 1345
Profile Input 586
Profile linkage with velocity changeover (overchange) 588
PS01: No memory module (error message) 669
PS02: Par. set invalid (error message) 669
PS03: Par. set device invalid (error message) 669
PS04: Par. set Mci invalid (error message) 670
PS07: Par. memory module invalid (error message) 670
PS08: Par. device invalid (error message) 670
PS09: Par. format invalid (error message) 670
PS10: Memory module binding invalid (error message) 670
PS11: Error
Lenze Setting Loaded (error message)
671
PS12: Parameter sets loaded (error message) 671
PS13: Parameter sets saved (error message) 671
PSM
Activate Lss sat. char. (C02859)
1146
Imax Lss saturation characteristic (C02855) 1146
Lss saturation characteristic (C02853) 1145
Maximum motor current field weakening (C00938) 1024
PTC 302
PW protection config MCI (C00510) 916
PW protection config X1(CAN) (C00509) 915
PW protection config X6(DIAG) (C00508) 914
PW protection internal config (C00506) 913
Q
Quick stop setting (C00104) 835
R
Ramp function generator (L_DFRFG) 1345
Rated device current (C00098) 834
Rated device currents (C00920) 1023
Rated device voltage (C00970) 1029
Rated heat amount of brake resist. (C00131) 840
Rated motor current (C00088) 832
Rated motor frequency (C00089) 832
Rated motor power (C00081) 831
Rated motor speed (C00087) 832
Rated motor torque (C00097) 833
Rated motor voltage (C00090) 832
Rated power - brake resistor (C00130) 840
Reduc. brake chopper threshold (C00174) 854
Reference setting 553
Referencing mode 556
Referential project 1242
Remote
Acceleration/deceleration time (C00461)
900
Control (C00462) 900
MCK control (C00463) 901
Monitoring timeout (C00464) 903
Setpoint selection (C00729) 964
Reset error message 651
Reset node (CAN) 707
Reset reference information 509
Reset time Imax/M controller (C00074) 829
Resp. to brake resist. overtemp. (C00574) 921
Resp. to CAN bus connection (C00592) 924
Resp. to CANx_IN monitoring (C00593) 925
Resp. to communication error with MCI (C01501) 1097
Resp. to control word error (C00594) 925
Resp. to controller limitations (C00570) 920
Resp. to current monitoring (C00584) 923
Resp. to DC-bus voltage (C00600) 928
Resp. to device overload (Ixt) (C00604) 928
Resp. to earth fault (C00602) 928
Resp. to fan failure (C00566) 919
Resp. to feedback (C00605) 929
Resp. to heatsink temp. > shutdown temp. -5°C (C00582) 923
Resp. to LS_SetError_x (C00581) 922
Resp. to mains phase failure (C00565) 919
Resp. to max. freq. feedb. DIG12/67 (C00607) 929
Resp. to max. speed at switching freq. (C00588) 924
Resp. to max. speed/output freq. reached (C00579) 922
Resp. to maximum current (C00609) 930
Resp. to maximum torque (C00608) 929
Resp. to motor overload (I²xt) (C00606) 929
Resp. to motor overtemp. PTC (C00585) 923
Resp. to motor phase failure (C00597) 927
Resp. to open circuit AINx (C00598) 927
Resp. to open circuit HTL encoder (C00586) 923
Resp. to operating system error (C00580) 922
Resp. to peak current (C00569) 919
Resp. to PLI monitoring (C00643) 945
Resp. to speed controller limited (C00567) 919
Resp. to switching frequency reduction (C00590) 924