Lenze 8400 - Page 1586

Index
1586 Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Resp. to too frequent AutoFailReset (C00189) 858
Resp. to wrong controller setting (C00571) 920
Retracting from limit switches 581
Reversing the phase sequence 275
Rotary table application 532
Rotor displacement angle detection after controller enable 226
RPDO1 communication parameter (I-1400) 765
RPDO1 mapping parameter (I-1600) 769
RPDO2 communication parameter (I-1401) 766
RPDO2 mapping parameter (I-1601) 770
RPDO3 communication parameter (I-1402) 767
RPDO3 mapping parameter (I-1602) 770
RPDO4 communication parameter (I-1403) 768
RPDO4 mapping parameter (I-1603) 771
Running time (C00180) 856
S
S_ShapingActive (status bit) 510
Safe stop 1 514
Safety functions 514
Safety instructions 26
Safety module 514
Saturation characteristic 224
SC
Depth of current setpoint filter (C00272)
868
Filter time const. DC detection (C00280) 869
Freq. current setpoint filter (C00270) 867
Max. acceleration change (C00274) 868
max. output voltage (C00276) 869
Optimisation of field feedforward control (C00576) 921
Settings (C00079) 830
Start motor magnetising current (C00918) 1022
Tdn speed controller (C00072) 828
Tn field controller (C00078) 830
Tn field weakening controller (C00578) 921
Vp field controller (C00077) 829
Vp field weakening controller (C00577) 921
Width of current setpoint filter (C00271) 868
Scaling of physical units 1197
Sd10: Speed limit for feedback system 12 (error message) 665
Sd11: Speed limit for feedback system 67 (error message) 665
Sd15: Open circuit HTL 4-fold (error message) 665
Sd3: Open circuit HTL 2-fold or 4-fold (error message) 665
SDO1 server parameter (I-1200) 762
SDO2 server parameter (I-1201) 763
Selection help for motor control 153
Selection of switching frequency 258
Selection of the control type 149
Sensibility - Setpoint feedforward control (C00653) 946
Sensorless control for synchronous machines (SLPSM) 151
Sensorless vector control (SLVC) 151, 192
Serial number (C00204) 860
Servo control (SC) 151, 231
Setpoint holding (C01239) 1078
Setpoint synchronisation ramp 535
Setting of compatibility (C02868) 1151
Setting of motor overload (I²xt) (C00120) 838
Setting the baud rate 705
Setting the error response 642
Setting the node address 705
Settings of measuring system (C02652) 1139
Short overview of error messages 653
Signal flow
Energy-saving V/f characteristic control (VFCplusEco)
176,
210
Sensorless vector control (SLVC) 194
Servo control (SC) 233
V/f characteristic control (VFCplus) 158, 159
V/f control (VFCplus + encoder) 186, 187, 193, 232
Signal type entry 1197
Slip calculation from equivalent circuit diagram (C02879) 1155
Slip comp. (C00021) 820
Slip compensation 271
Slip regulator 189
SLPSM
Controlled current setpoint (C00995)
1035
Filter cutoff frequency (C00997) 1036
Filter time rotor position (C00998) 1036
PLL gain (C00999) 1036
Switching speed (C00996) 1035
SLVC
Gain of cross current controller (C00986)
1033
Gain of field current controller (C00985) 1033
Software limit positions 536
Source of diff. setpoint feedforward control (C00654) 946
Speed control with torque limitation (SC) 235
Speed control with torque limitation (SLVC) 195
Speed feedback 152
Speed follower 551
Speed limitation (C00909) 1021
Speed override 602
Speed sensor selection (C00495) 911
Speed setpoint generation 535
S-ramp smoothing override 604
S-ramp time for jerk limitation 591
SS1 514
StandBy (MCK operating mode) 513
State machine (MCK) 512
Status "Drive in target" 541
Status "Reference known" 509
Status determining error (16-bit) (C00160) 847
Status determining error (C00168) 853
Status displays 624
Status of brake output BD (C00117) 838
Status of last device command (C00003) 812
Status word (C00150) 844
Status word (MCK) 507
Stop 597
Stop of the ramp function generator 289