Lenze 8400 - Page 1587

Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23 1587
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Stop the ramp function generator 289
Stuff-bit error 748
Su02: One mains phase is missing (error message) 656
Su03: Too frequent mains switching (error message) 656
Su04: CU insufficiently supplied (error message) 657
Su06: Mains input overload (error message) 657
Su07: 24V supply off (error message) 657
Switching cycles (C00177) 855
Switching freq. reduct. (Temp.) (C00144) 843
Switching frequency 258
Switching frequency (C00018) 819
Switching status of the fans (C00560) 917
Switch-on inhibit 123
Sync correction width (C01124) 1062
Sync cycle time setpoint (C01121) 1061
Sync phase position (C01122) 1061
Sync signal source (C01120) 1060
Sync telegram 733
Sync window (C01123) 1061
Synchronisation mode 1362
Synchronous motor
Field weakening
228
SyncTxRxTimes (C00370) 885
System blocks 1529
System bus 700
System connection list
16-bit (C00620)
931
Angle (C00622) 941
Bool (C00621) 934
System error messages 647
System runtimes (C00312) 871
T
Target group 21
Target position monitoring 541
Task selection 1201
Teaching of the position 596
Technology applications 29
Temperature inside the controller (C00062) 826
Terminals 322
Analog terminals 347
Digital input terminals 323
Digital output terminals 344
For electrical data see the hardware manual
User-defined terminal assignment
365
Thermal motor load (I²xt) (C00066) 827
Ti current controller (C00076) 829
Ti speed controller (C00071) 828
Time settings (C00181) 856
Torque (C00056) 825
Torque control with speed limitation (SC) 237
Torque control with speed limitation (SLVC) 196
Torque feedforward control (SC) 245
Torque feedforward control (SLVC) 202
Torque limitation 169
Touch probe detection 357
TP
Edge selection (C02810)
1139
Pos. window end (C02814) 1141
Pos. window start (C02813) 1140
Position offset (C02812) 1140
Position source (C02815) 1141
Sensor delay (C02811) 1140
Signal counter (C02816) 1141
TouchProbe position (C02817) 1142
TP (touch probe) 357
TPDO1 communication parameter (I-1800) 772
TPDO1 mapping parameter (I-1A00) 777
TPDO2 communication parameter (I-1801) 774
TPDO2 mapping parameter (I-1A01) 777
TPDO3 communication parameter (I-1802) 775
TPDO3 mapping parameter (I-1A02) 778
TPDO4 communication parameter (I-1803) 776
Transmission mode CAN Rx PDOs (C00323) 873
Transmission mode CAN TxPDOs (C00322) 872
Transmission type 731
Travel range monitoring 539
U
Ultimate motor current 301
Ultimate motor current (C00939) 1024
USB diagnostic adapter 33
User data 737
User error 1 (error message) 677
User error 2 (error message) 678
User error 3 (error message) 678
User error 4 (error message) 678
User error 5 (error message) 678
User error 6 (error message) 678
User error 7 (error message) 678
User error 8 (error message) 679
User level 36
User menu 41
User menu (C00517) 916
User-definable V/f characteristic 171
V
V/f base frequency 164
V/f characteristic control (VFCplus) 150, 157
V/f control (VFCplus + encoder) 185
V/f emergency operation in case of encoder open circuit 185,
231, 321
Validity of the reference measuring system 509
VFC
Frequency interpol. point n (C00967)
1028
Limitation V/f + sensor (C00971) 1030
Ti V/f +sensor (C00973) 1030
Time const. slip comp. (C00966) 1028
V/f base frequency (C00015) 818