Optek C4101 - User Manual

To Next Page

Instruction Manual

optek-converter C4101

Version 07.2009_1.2US

PN: 1004-1001-02 (-52)

optek-Danulat GmbH

Emscherbruchallee 2

45356 Essen

Phone: +49-(0)201-63409-0

Fax: +49-(0)201-63409-999

E-Mail: info@optek.de

Internet: www.optek.com

Section 1 of 2

Main Page

Table of Contents4
Using the Instruction Manual9
Validity of the Instruction Manual9
Explanation of the Converter Model Number10
Pictograms and Signal Words11
Intended Use12
Safety13
General Safety Instructions13
Safety Instructions for Works on Electrical Equipment14
Description of the Converter15
Front View Converter C400017
Rear View Converter C410118
Technical Data19
Possible Sensors21
Dimensions Control 400022
Front Panel Mounting IP65 (Option)23
Dimensions for Additional Housing B19-42 - Plastic - IP66 (Option)24
Additional Housing S19-42 - Stainless Steel 1.4301 / SS304 - IP65 (Option)25
Installation of the Converter26
Installation Site Requirements for Standard Installation26
Standard Installation26
Installation for IP65 (Option)27
Wiring28
General Advice on Wiring28
Connecting the Voltage Supply 115 or 230 V AC29
Connecting the Voltage Supply 24 V AC / DC (Option)30
Connecting the Sensors31
Wiring Plan AF16 to C4101 or C420133
Wiring Plan AS16 or AS56 to C4101 or C420134
Wiring Plan AS16-BT to C4101 or C420135
Connecting the Relay Outputs36
Connecting the Ma-Outputs38
Commissioning39
Requirements for Commissioning39
Switching the Converter on39
Adjusting Lamp Voltage40
Other Activities When Commissioning42
Software Version C43
Starting the Software43
General Software Information45
General Information on Operating the Software45
Information on the Measuring Mode49
Choosing the Language50
Language / Sprache50
Carrying out System Settings Prior to Initial Commissioning51
System Settings - Display51
System Settings - Date / Time53
System Settings - Lamp Voltage54
System Settings - Optek Inputs56
System Settings - Ma-Inputs58
Entering Products in the Software59
Product Configuration59
Define Product Name61
Define Measuring Results62
Define Measuring Result Name65
Measuring Result - Define Function66
Measuring Result - Multiplication with Ma-Input71
Measuring Result - Multiplication with Linearization72
Measuring Result - Multiplication with Slope + Offset73
Measuring Result - Measuring Range Beginning and End74
Measuring Result - Measuring Range, Unit and Format75
Define Linearization77
Linearization - Define Table Name78
Linearization - Define Tables79
Define Offset + Slope Set81
Offset + Slope - Define Set Name82
Determine Offset + Slope83
Define Limit Values84
Limit Value - Selecting Measuring Result86
Limit Value - Define Limit Value87
Limit Value - Define Delay Time88
Alarm Type88
Limit Value - Define Alarm Type89
Low Alarm89
Define Display90
Display Formula92
Product Change94
Measurement Display96
Selecting Display Mode96
Data Logger Display97
Operating Principle of the Data Logger97
Displaying the Data Logger99
Erasing the Data Logger102
Switching off the Data Logger102
PC-Transfer102
System Information Display103
Viewing Configuration103
System Settings Display105
Sensor Data Display107
System Settings108
Display109
Date / Time109
Data Logger112
Damping114
Lamp Voltage115
System Zero Point116
Maintenance Menu117
Product Change118
Sensor TF120
Zero Point121
Ma-Outputs123
9.10.10 Relay Outputs125
9.10.11 Remote in127
9.10.12 Hold129
9.10.13 Failsafe131
Password Protection133
9.10.14.1 Password Definition133
9.10.14.2 Password Allocation135
9.10.14.3 Password Duration137
Optek Inputs139
9.10.16 Ma-Inputs139
System Data Sensors 1 to 4139
9.10.18 Fieldbus141
Maintenance143
Hold Manually143
Setting System Zero Point145
System Zero Point Manually145
System Diagnostics148
Sensor Adaptation150
Calibration Scattered Light152
Calibration Ma-Inputs154
Calibration Ma-Outputs156
Service158
Enter Password158
Entering Password159
Monitors160
Lamp Monitor161
Detector Monitor163
Measuring Result Monitor165
Ma Monitor166
Relay + LED Monitor167
Remote in Monitor168
Subassembly Monitor169
PC Transfer171
Reset Converter173
Control Via an External Control System (Remote)174
Input Signals from Control System - Remote in174
Remote in Monitor174
Product Change, Setting the System Zero Point and the Hold Function in the Remote in 1 Function176
Product Change, Setting the System Zero Point and the Hold Function in the Remote in 2 Function177
Output Signals of the Converter - Remote out179
Status Feedback Via the Remote out 1 Function179
Status Feedback Via the Remote out 2 Function181
Status Feedback Via the Remote out 3 Function183
Status Feedback Via Ma-Output184
Factory Settings185
Define Measuring Result Menu185
Lim. Value Menu185
Define Display Menu186
Display Settings Menu186
Error Messages187
Signal Loss187
Lamp Failure189
Communication Error191
Messages Triggering System Alarm193
Settings Error Messages194
Switch-On Error Messages196
Faults198
Spare Parts and Accessories200
Accessories Converter200
Small Parts Fuses200
Appendix201
Installation Documentation - Hardware202
TÜV NORD CERT Gmbh "GS-Mark203
QM System Certificate206
Declaration of Conformity207
Response Via Fax208

Need help?

Do you have a question about the Optek C4101 and is the answer not in the manual?

Optek C4101 Specifications

General

Brand	Optek
Model	C4101
Category	Media Converter
Language	English

Related product manuals

Optek C4101 - User Manual

Table of Contents

Optek C4101 Specifications

Related product manuals