Korg Kronos - Page 106

Creating songs (Sequencer mode)
100
Listen to the recorded result
10.IntheP0:Play/REC–AudioTRACKMixerpage,
mutetheplaybackofbothaudiotracks1and2.
Play/Rec/Mute:Mute
SoloOn/Off:Off
11.PresstheSEQUENCERSTART/STOPswitchto
playbackthesong.
Makeoutputsettingsforaudiotrack3asdescribed
in“Listentotherecordedresult”onpage 96.
12.PresstheSEQUENCERST
ART/STOPswitchto
stopplayback.
IfyouwanttocreateaWAVEfileonthediskfroma
songthatincludesaudiotracks,see“Resamplinga
songtocreateaWavefile”onpage 152.
Recording automation events for pan,
EQ, and volume etc. on an audio track
Allaudiotrackparameters(Pan,Volu me,Send1/2,
andEQ)canberecordedinrealtime.Inthisexample,
we’llrecordPanandVolum echangesonaudiotrack3.
GototheP0:Play/REC–AudioTrackMixerpage,and
use“TrackSelect”toselectAudioTrack03asthetrack
toberecorded.Yo
ucouldusetheVALUEcontrollerto
operateadesiredparameter,butusingthecontrol
surfaceletsyoumixuptoeighttrackssimultaneously.
Setup
1. GototheP0:Play/REC–Preferencepage.
2. InRecordingSetup,RecordingSetup(Audio
Track),choosethedesiredrecordingmethod.
Inthisexample,we’llchooseoverdubrecordingso
thatwecanrecordrepeatedpasses,addingmore
automationdataoneachpass.
–RecordingSetup–
Overdub:on
–RecordingSetup(AudioTrack)–
AutomationOnly:ch
ecked
Ifyourecordwithoutchecking“AutomationOnly,”
audioeventswillalsoberecorded.Notethatthis
willeraseandoverwritetheaudioeventsthat
alreadyexist.
3. GototheP0:Play/REC–ControlSurfacepage.
4. PresstheCONTROLASSIGNAUDIOswitch
severaltimessothattheHDR1–8LEDlocatedat
therightofthesw
itchislit.
5.
InthecenteroftherightedgeoftheLCD,check
“LinkKBDRECTrktoCtrlSurface.”
IfyoucheckthisandpresstheMIXSELECT3
switch,eachknobwillcontrolaudiotrack3,andat
thesametime“TrackSelect”willswitchtoAudio
Track03.
PresstheSEQUENCERSTART/STOPswitchtoplay
back,andoperatetheknobsandslidersetc.to
rehearseyourmix.
IfMIXERKNOBissettoCHANNELSTRIP,knob1
willcontrolpan,knobs2–6willcontrolEQ,and
knobs7and8willcontrolthesendlevels.Useslider
3toadjustthevolumeofaudiotrack3.
Whenyou’vefinishedrehearsing,pressthe
SEQUENCERSTART/STOPswitchtostop.
PresstheLOCATEswitch.
Record
6. PresstheSEQUENCERREC/WRITEswitch.
Themetronomewillbeginsounding,andyouwill
beinrecord‐readymode.
7. PresstheSEQUENCERSTART/STOPswitch.
Afteratwo‐measurecount,recordingwillbegin.
Usetheslidersetc.tocontrolthevolume.
Note:Whenrecordingautomationevents,youcan
usequantization,theresolutionsetting,andthe
comparefunctioninthesam
ewa
yasforaMIDI
track.
8. Whenyou’refinishedrecording,pressthe
SEQUENCERSTART/STOPswitchtostop
recording.
9. Listentotherecordedresult.
PresstheSEQUENCERSTART/STOPswitchtoplay
back.
Ifyouwanttorecordagain,usetheCompare
function(presstheCOMPAREswitch)tore‐record.
10.Ifyo
uwanttocontinueaddingautomationevents,
repeattherecordingprocedurefromstep6.