Korg Kronos User Manual

Appendices
264
Not enough sample memory
Meaning:Thereisinsufficientsamplememory(for
sampleparametersorsamplewaveformdata).
• Deletesamplestoincreasetheamountoffree
memory.
Not enough sample/multisample
locations available
Meaning:Thedatayouattemptedtoloadwould
exceedthemaximumnumberofmultisamplesor
samples.Tosolvethisproblem:
•InSamplingmode,useDeleteMultisampleor
DeleteSampletofreeasufficientnumber,and
reloadthedata.‘
Not enough song locations available
Meaning:Whenloadinga.SNGfilewithAppend
specified,youattemptedtoloadmoresongsthancan
beloaded.
Meaning:WhenexecutingAutoSongSetup,anew
songcouldnotbeselectedautomaticallybecausethere
wasnosongwiththedefaultsettings.Thiscanbe
causedbyusingtheGlobalmode“Changeallbank

references”commandwiththeSongoptionselected,
sincethismodifiesthesettingsofallsongsawayfrom
thedefaults;afterthis,thesystemwillnotrecognize
thosesongsasbeingemptyandavailable.
•InSequencermode,usetheInitializeSong
commandtoincreasethenumberofSongsthatcan
beus
ed
,andthenloadthesongagain.
Not enough song memory
Meaning:WhenexecutingtheSamplingmodeTime
SliceorSavecommands,thetotaldataforallsongs
occupiesallofthesequencedatamemoryarea,sothat
savingisnotpossible.
Meaning:WhensamplingtoRAMinSequencermode,
itisnotpossibletocreatetrackdataatthesametime.
• Increasetheamountoffreememory
,forexample
bydeletinganothersong.
No unused WAVE files found
Meaning:WhenyouexecutedtheDiskUtilitypage
menucommandDeleteUnusedWAVEfiles,no
unusedWAVEfileswerefound.
O (Obey copyright rules–Oscillator)
Obey Copyright Rules
Meaning:WhenyouexecutetheDiskmodeMake
AudioCDpageWritetoCDcommand,orwhenyou
executeDestinationintheSamplingmodeAudioCD
pageDestinationcommand.
Pleaseread“COPYRIGHTWARNI NG”onpage 3of
theQuickStartGuidebeforeyouusethisdata.
Oscillator Mode conflicts (Check PROG
P1)
Meaning:InSamplingmodewhenyouexecuted
ConvertMSToProgramwithUseDestination
ProgramParameterschecked,theconversion
destinationprogramOscillatorModesettingdidnot
match.
•InProgrammode,settheOscillatorModeofthe
conversiondestinationprogram.Ifconvertinga
monauralmultisample,selectSingle.Ifconvertinga
stereomultisample,selectDo
uble.
P (Pattern–Program)
Pattern conflicts with events
Meaning:ItwasnotpossibletoexecutetheBounce
operationbecauseoneofthetrackscontaineda
pattern,andthesamemeasureoftheothertrack
containedeventsorapattern.
•Openthepattern.
Pattern exists across destination to-end-
of-measure or source from-measure
Meaning:Whenmovingameasure,theeditoperation
couldnotbeexecutedbecauseapatternhadbeenput
inthedestinationendmeasureorthesourcestart
measure,andhadnotbeenopened.
•Openthepattern.
Pattern exists in destination or source
track - Open pattern?
Meaning:Apatternhasbeenplacedinthetrackthat
youspecifiedasadestinationorsourceforediting.If
youwishtoopenthepatternandexecute(theeventsof
thepatternwillbecopied),presstheOKbutton.Ifyou
wishtoexecutewithoutopeningthepattern,pressthe
Ca
nc
elbutton.
Pattern used in song - Continue ?
Meaning:Whenediting,thespecifiedpatternhasbeen
placedinatrack.Ifyouwishtoexecute,presstheOK
button.Ifyoudecidenottoexecute,presstheCancel
button.

Korg Kronos Specifications

Operating Environment

operating temperature range	+5 – +35 °C

Power

power consumption	60 W

Weight and Dimensions

dimensions (61 keys)	1052 x 362 x 134 mm
dimensions (73 keys)	1243 x 411 x 145 mm
dimensions (88 keys)	1455 x 411 x 145 mm
weight (61 keys)	12.5 kg
weight (73 keys)	20.3 kg
weight (88 keys)	23.0 kg