Korg Kronos - HD-1 Program; EXi Program; AL-1 Program

Error and confirmation messages R (Rear sample–Root)
265
Program Bank Type conflicts
Meaning:Whenreceivingadumpofanindividual
bankorasingleprogram,theKRONOSreceiveda
programthatdidnotmatchthebanktype.Ifthebank
typedoesnotmatch,theprogramwillnotbereceived.
Meaning:WhenreceivinganAllProgramsdump,the
KRONOSreceivedabankwhosebankty
pedi
dnot
match.Onlybanksofthematchingbanktypewillbe
received.
•Ifyou’rereceivingbanksUSER‐A…GorAA…GG,
useGlobalSetProgramUser‐BankTypetochange
thebanktypesothatit’sthesameastheonebeing
transmitted.Thentrytheoperationagain.
Program Type conflicts
Meaning:Thismessagewillappearwhenyouexecute
CopyToneAdjustifthecopy‐sourceandcopy‐
destinationprogramtypesaredifferent.Youcannot
copybetweenHD‐1andEXiPrograms,orbetween
differenttypesofEXiPrograms.
R (Rear sample–Root)
Rear sample is empty
Meaning:WhenyouexecutedLinkintheSampling
modeSampleEditpage,thesamplethatyouspecified
astherearsampleisempty.
•Specifyasamplethatcontainsdataastherear
sample,andexecuteonceagain.
Root directory is full
Meaning:Youattemptedtocreateafileordirectoryin
therootdirectoryofthemedia,butthiswouldexceed
themaximumnumberofrootdirectoryentries.
•Eitherdeleteanexistingfileordirectory,orOpena
directorytomovedownonelevelbeforeexecuting
onceagain.
S (Sample–Source)
Sample data used in other sample(s)
Continue?
Meaning:Othersample(s)usethesamesampledataas
thesamplethatyouareediting.Tocontinueediting,
presstheOKbutton.
Sample L and R are identical
Meaning:Theeditoperationcouldnotbeexecuted
becausethedestination(savelocation)LandRsample
numbersareidentical.
•SelectdifferentsamplenumbersforLandRofthe
destination(savelocation).
Sample length is shorter than minimum
Meaning:Youattemptedtoexecuteanediting
operationthatwouldmakethesampledatashorter
than8samples.
• Changetheeditingrangesothatthesampledata
willbelongerthan8samples.
Sample used in other multisample(s)
Continue?
Meaning:Thesampleyouareeditingisusedbyother
multisamples.Tocontinueediting,presstheOK
button.
Selected file/path is not correct
Meaning:Whenloadingadivided.PCGfile,you
attemptedtoloada.PCGfileofthesamenamethat
wasnotdividedorhaddifferingcontents.
•Loadthecorrect.PCGfile.
Meaning:WhenloadingaKSFfilethatwassplitacross
multiplemedia,theorderinwhichyouattemptedto
loadthef
ileswasincorrect.
•LoadtheKSFfileinthecorrectorder.Toviewthe
filenumberorderinwhichtheKSFfileswere
saved,youcanchecktheTranslationpagemenu
command.(Thesamplenameandnumberofthe
firstKSFfilewillbedisplayed.)
Slice point over limit
Can’t divide
Meaning:WhenusingtheSamplingmodeTimeSlice
orTimeStretchcommands,theSlicesettingwould
dividethesampleintomoresamplesthanthe
maximumpossiblenumber(1000),andthusDivide
cannotbeexecuted.
•UseLinktoconnectanyIndexthatyoudonot
require,andthenexecuteDivide.
Source file is not 44100Hz or 48000Hz
Can’t convert
Meaning:WhenexecutingtheDiskmodeUtilitypage
menucommandRateConvert,youselectedaWAVE
fileofasamplingrateotherthan44.1kHzor48kHz.
•YoucannotconvertWAVEfilesotherthan44.1kHz
or48kHz.