vi Instruction Manual QuickTOC
®
ultra
IECEx 12E5119
LAR | PROCESS ANALYSERS AG
9.2.6.1 Once all test criteria are met, proceed with the next stepSoda Lime ............ 212
9.2.6.2 Tube Connections ......................................................................................... 212
9.2.6.3 Pre Pressure of the Carrier Gas ...................................................................212
9.2.7 Perform Care and Maintenance Actions (Ambient Air Preparation Unit) .............. 213
9.2.7.1 Replace Soda Lime ......................................................................................213
9.2.7.2 Replace Gas Filter ........................................................................................ 214
9.2.7.3 Replace Filter Mats .......................................................................................216
9.2.7.4 Replace Fine Filter Unit ................................................................................ 216
9.2.7.5 Replace Coarse Filter Unit ............................................................................217
9.2.7.6 Replace Activated Carbon ............................................................................217
9.3 Proceed analogously to the replacement of the soda lime in Chapter 9.2.7.1 from
page 213FlowSampler® .....................................................................................................................218
9.3.1 Variants of FlowSampler® .................................................................................... 218
9.3.2 FlowSampler® DN25 ............................................................................................ 219
9.3.3 FlowSampler® DN17 ............................................................................................ 220
9.3.4 Installation of the FlowSampler® .......................................................................... 221
9.3.5 Start-Up of the FlowSampler®.............................................................................. 221
9.3.6 Care and Maintenance Actions (FlowSampler®).................................................. 222
9.3.7 Perform Visual Inspections (FlowSampler®) ........................................................ 223
9.3.7.1 Flow .............................................................................................................. 223
9.3.7.2 Sampling Pipe (Needle) ................................................................................ 223
9.3.8 Perform Care and Maintenance Actions (FlowSampler®).................................... 224
9.3.8.1 Clean Sampling Pipe (Needle) .....................................................................224
9.3.8.2 Clean FlowSampler® ....................................................................................224
9.4 Overflow Sampler ..............................................................................................................225
9.4.1 Construction of the Overflow Sampler .................................................................. 225
9.4.2 Connections.......................................................................................................... 225
9.4.3 Set-Up................................................................................................................... 226
9.4.4 Care and Maintenance (Overflow Sampler).......................................................... 227
9.4.5 Perform Visual Inspection (Overflow Sampler)..................................................... 228
9.4.5.1 Flow .............................................................................................................. 228
9.4.6 Perform Care and Maintenance (Overflow Sampler)............................................ 228
9.4.6.1 Clean Overflow Sampler ...............................................................................229
9.5 CO2-Remover ................................................................................................................... 230
9.5.1 Procedure of compressed air drying and CO2 removal........................................ 230
9.5.2 Construction of the CO2-Remover........................................................................ 230
9.5.3 Installation of the CO2-Remover........................................................................... 231
9.5.4 Start-Up of the CO2-Remover .............................................................................. 232
9.5.5 Care and Maintenance Actions (CO2-Remover) .................................................. 233
9.5.6 Perform Visual Inspections (CO2-Remover)......................................................... 234
9.5.6.1 Housing ......................................................................................................... 234
9.5.6.2 Service Lamp ................................................................................................234
9.6 Mounting Rack ..................................................................................................................235
9.7 Trackball ............................................................................................................................ 237
9.8 Multi Stream Option .......................................................................................................... 238
9.9 Multi Parameter Option .....................................................................................................239
9.10 High Salt Option ..............................................................................................................240
9.11 Auto-TIC-Port .................................................................................................................. 241
9.11.1 Construction of the TIC Reactor with Auto-TIC-Port........................................... 241
9.11.2 Start-Up of the TIC Reactor with Auto-TIC-Port.................................................. 241
9.11.3 Care and Maintenance Actions (Auto-TIC-Port) ................................................. 242
9.11.4 Perform Visual Inspections (Auto-TIC-Port)........................................................ 243
9.11.4.1 Microswitch on Auto-TIC-Port (6 Months) ................................................... 243
9.11.5 Perform Care and Maintenance Actions (Auto-TIC-Port) ................................... 244
9.11.5.1 Replace Needle Guide Seal (Auto-TIC-Port) (1 Month) .............................244
9.11.5.2 Clean Needle Guide (Auto-TIC-Port) (1 Month) ......................................... 245
9.11.6 Clean and oil Auto-TIC-Port (3 Months).............................................................. 246
9.12 Internal Sample Dilution ..................................................................................................247
To Next Page
Loading...