Parameter List
10
10.8 E: Motor Parameters
YASKAWA ELECTRIC SIEP C710617 05F YASKAWA AC Drive GA700 Technical Manual 527
No.
(Hex.)
Name Description
Default
(Range)
Ref.
E2-09
(0316)
Expert
Motor Mechanical
Loss
Sets the mechanical loss of the motor. Motor rated power (kw) =
100.0%. Usually it is not necessary to change this setting.
0.0%
(0.0 - 10.0%)
808
E2-10
(0317)
Motor Iron Loss
Sets the motor iron loss.
Determined by o2-
04 and C6-01
(0 - 65535 W)
808
E2-11
(0318)
Motor Rated Power
(kW)
Sets the motor rated power in 0.01 kW increments. (1 HP = 0.746
kW)
Determined by o2-
04 and C6-01
(0.00 - 650.00 kW)
809
◆ E3: V/f Pattern for Motor 2
No.
(Hex.)
Name Description
Default
(Range)
Ref.
E3-01
(0319)
Motor 2 Control
Mode Selection
Sets the control method for motor 2.
Note:
When you change this setting, the drive will set all parameters
that are dependent on this parameter to their default settings.
0 : V/f Control
1 : V/f Control with Encoder
2 : Open Loop Vector
3 : Closed Loop Vector
0
(0 - 3)
809
E3-04
(031A)
Motor 2 Maximum
Output Frequency
Set the maximum output frequency for the motor 2 V/f pattern.
Determined by E3-
01
(40.0 - 590.0 Hz)
810
E3-05
(031B)
Motor 2 Maximum
Output Voltage
Sets the maximum output voltage for the motor 2 V/f pattern.
Determined by E3-
01
(200 V Class: 0.0 -
255.0 V,
400 V Class: 0.0 -
510.0 V)
810
E3-06
(031C)
Motor 2 Base
Frequency
Sets the base frequency for the motor 2 V/f pattern.
Determined by E3-
01
(0.0 - E3-04)
810
E3-07
(031D)
Motor 2 Mid Point
A Frequency
Sets a middle output frequency for the motor 2 V/f pattern.
Determined by E3-
01
(0.0 - E3-04)
810
E3-08
(031E)
Motor 2 Mid Point
AVoltage
Sets a middle output voltage for the motor 2 V/f pattern.
Determined by E3-
01
(200 V Class: 0.0 -
255.0 V,
400 V Class: 0.0 -
510.0 V)
810
E3-09
(031F)
Motor 2 Minimum
Output Frequency
Sets the minimum output frequency for the motor 2 V/f pattern.
Determined by E3-
01
(0.0 - E3-04)
810
E3-10
(0320)
Motor 2 Minimum
Output Voltage
Sets the minimum output voltage for the motor 2 V/f pattern.
Determined by E3-
01
(200 V Class: 0.0 -
255.0 V,
400 V Class: 0.0 -
510.0 V)
810
E3-11
(0345)
Expert
Motor 2 Mid Point
B Frequency
Sets a middle output frequency for the motor 2 V/f pattern. Set this
parameter to adjust the V/f pattern for the constant output range.
Usually it is not necessary to change this setting.
0.0 Hz
(0.0 - E3-04)
811
To Next Page
Loading...
