YASKAWA GA700 - Yaskawa SST4 Series IPM Motors (Constant Torque)

10.22 Parameters Changed by PM Motor Code Selection
660 YASKAWA ELECTRIC SIEP C710617 05F YASKAWA AC Drive GA700 Technical Manual
No. Name Unit Motor Code (setting value of E5-01)
E1-06 Base Frequency Hz 57.5 57.5 57.5 57.5
E1-09
Minimum Output
Frequency
Hz 2.9 2.9 2.9 2.9
C5-17 Motor Inertia kgm
2
0.56 0.83 0.96 1.61
L3-24
*1
Motor Accel Time for
Inertia Cal
s 0.147 0.161 0.154 0.212
n5-02
Motor Acceleration
Time
s 0.147 0.161 0.154 0.212
n8-49
d-Axis Cur
forHighEfficiencyCont
% -12.5 -28.8 -13.3 -11.6
*1 Default settings vary depending on the setting of o2-04 [Drive Model Selection].
◆ Yaskawa SST4 Series IPM Motors (Constant Torque)
Table 10.21 SST4 Series Motor Code Setting for Specification of 200 V at 1750 min
-1
(r/min)
No. Name Unit Motor Code (setting value of E5-01)
E5-01
PM Motor Code
Selection
- 2202 2203 2205 2206 2208 220A 220B 220D
Voltage Class V 200 200 200 200 200 200 200 200
Capacity kW 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11
Motor Rotation
Speed
min
-1
1750 1750 1750 1750 1750 1750 1750 1750
E5-02
PM Motor Rated
Power (kW)
kW 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11.0
E5-03
PM Motor Rated
Current (FLA)
A 1.77 3.54 6.56 8.96 14.79 20.94 29.58 41.1
E5-04
PM Motor Pole
Count
- 6 6 6 6 6 6 6 6
E5-05
PM Motor
Resistance (ohms/
phase)
Ω 2.247 1.132 0.774 0.479 0.242 0.275 0.161 0.111
E5-06
PM d-axis
Inductance (mH/
phase)
mH 22.32 12.38 8.90 7.39 5.06 5.82 3.86 3.59
E5-07
PM q-axis
Inductance (mH/
phase)
mH 32.50 15.72 11.96 9.63 6.42 6.74 4.66 4.32
E5-09
PM Back-EMF
Vpeak (mV/(rad/
s))
mVs/rad 215.2 203.9 219.3 230.6 235.1 251.7 235.7 252.0
E5-24
PM Motor
Induced Voltage
Constant 2 (Ke)
mV/(r/
min)
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
E1-04
Maximum Output
Frequency
Hz 87.5 87.5 87.5 87.5 87.5 87.5 87.5 87.5
E1-05
Maximum Output
Voltage
V 190.0 190.0 190.0 190.0 190.0 190.0 190.0 190.0
E1-06 Base Frequency Hz 87.5 87.5 87.5 87.5 87.5 87.5 87.5 87.5
E1-09
Minimum Output
Frequency
Hz 4.4 4.4 4.4 4.4 4.4 4.4 4.4 4.4
C5-17 Motor Inertia kgm
2
0.0016 0.0022 0.0042 0.0081 0.0133 0.013 0.017 0.027
L3-24
*1
Motor Accel Time
for Inertia Cal
s 0.134 0.099 0.094 0.124 0.121 0.081 0.075 0.082