Table of Contents
7.7.1.2 Conditional Output ........................................................ 173
7.7.1.3 Groundwater Pump Test ................................................ 173
7.7.1.4 Miscellaneous Features .................................................. 176
7.7.1.5 PulseCountReset Instruction .......................................... 178
7.7.1.6 Scaling Array ................................................................. 179
7.7.1.7 Signatures: Example Programs ...................................... 180
7.7.1.7.1 Text Signature ..................................................... 180
7.7.1.7.2 Binary Runtime Signature................................... 180
7.7.1.7.3 Executable Code Signatures ............................... 180
7.7.1.8 Use of Multiple Scans .................................................... 181
7.7.2 Data Input: Loading Large Data Sets ....................................... 182
7.7.3 Data Input: Array-Assigned Expression ................................... 183
7.7.4 Data Output: Calculating Running Average ............................. 187
7.7.5 Data Output: Two Intervals in One Data Table ........................ 191
7.7.6 Data Output: Triggers and Omitting Samples .......................... 192
7.7.7 Data Output: Using Data Type Bool8 ...................................... 193
7.7.8 Data Output: Using Data Type NSEC ...................................... 198
7.7.8.1 NSEC Options ............................................................... 198
7.7.9 Data Output: Wind Vector ....................................................... 201
7.7.9.1 OutputOpt Parameters ................................................... 202
7.7.9.2 Wind Vector Processing ................................................ 202
7.7.9.2.1 Measured Raw Data ............................................ 203
7.7.9.2.2 Calculations ........................................................ 204
7.7.10 Displaying Data: Custom Menus — Details ............................ 207
7.7.11 Field Calibration — Details ..................................................... 214
7.7.11.1 Field Calibration CAL Files .......................................... 214
7.7.11.2 Field Calibration Programming ..................................... 215
7.7.11.3 Field Calibration Wizard Overview ............................... 215
7.7.11.4 Field Calibration Numeric Monitor Procedures............. 215
7.7.11.4.1 One-Point Calibrations (Zero or Offset) ............. 216
7.7.11.4.2 Two-Point Calibrations (gain and offset) ............ 217
7.7.11.4.3 Zero Basis Point Calibration ............................... 217
7.7.11.5 Field Calibration Examples ........................................... 217
7.7.11.5.1 FieldCal() Zero or Tare (Opt 0) Example ........... 218
7.7.11.5.2 FieldCal() Offset (Opt 1) Example ..................... 220
7.7.11.5.3 FieldCal() Slope and Offset (Opt 2) Example ..... 223
7.7.11.5.4 FieldCal() Slope (Opt 3) Example ...................... 225
7.7.11.5.5 FieldCal() Zero Basis (Opt 4) Example .............. 228
7.7.11.6 Field Calibration Strain Examples ................................. 228
7.7.11.6.1 FieldCalStrain() Shunt Calibration Concepts...... 228
7.7.11.6.2 FieldCalStrain() Shunt Calibration Example ...... 229
7.7.11.6.3 FieldCalStrain() Quarter-Bridge Shunt
Example ........................................................... 231
7.7.11.6.4 FieldCalStrain() Quarter-Bridge Zero ................. 232
7.7.12 Measurement: Fast Analog Voltage ......................................... 233
7.7.12.1
Tips — Fast Analog Voltage ......................................... 237
7.7.13 Measurement: Excite, Delay, Measure ..................................... 239
7.7.14 Serial I/O: SDI-12 Sensor Support — Details .......................... 240
7.7.14.1 SDI-12 Transparent Mode ............................................. 240
7.7.14.1.1 SDI-12 Transparent Mode Commands ............... 241
7.7.14.2 SDI-12 Recorder Mode .................................................. 246
7.7.14.2.1 Alternate Start Concurrent Measurement
Command ........................................................ 248
7.7.14.2.2 SDI-12 Extended Command Support ................. 253
7.7.14.3 SDI-12 Sensor Mode ..................................................... 253
To Next Page
Loading...
