Campbell CR800 Series - Page 21

Table of Contents
21
FIGURE 44: Bool8 Data from Bit Shift Example (Numeric Monitor) ....... 195
FIGURE 45: Bool8 Data from Bit Shift Example (PC Data File) .............. 196
FIGURE 46: Input Sample Vectors ............................................................ 204
FIGURE 47: Mean Wind-Vector Graph ..................................................... 205
FIGURE 48: Standard Deviation of Direction ............................................ 206
FIGURE 49: Standard Deviation of Direction ............................................ 206
FIGURE 50: Custom Menu Example — Home Screen .............................. 209
FIGURE 51: Custom Menu Example — View Data Window .................... 209
FIGURE 52: Custom Menu Example — Make Notes Sub Menu ............... 209
FIGURE 53: Custom Menu Example — Predefined Notes Pick List ......... 210
FIGURE 54: Custom Menu Example — Free Entry Notes Window .......... 210
FIGURE 55: Custom Menu Example — Accept / Clear Notes Window .... 210
FIGURE 56: Custom Menu Example — Control Sub Menu ...................... 211
FIGURE 57: Custom Menu Example — Control LED Pick List ............... 211
FIGURE 58: Custom Menu Example — Control LED Boolean Pick
List ....................................................................................................... 211
FIGURE 59: Quarter-Bridge Strain Gage with RC Resistor Shunt ............ 230
FIGURE 60: Strain Gage Shunt Calibration Start ....................................... 231
FIGURE 61: Strain Gage Shunt Calibration Finish .................................... 232
FIGURE 62: Zero Procedure Start .............................................................. 232
FIGURE 63: Zero Procedure Finish ............................................................ 232
FIGURE 64: Entering SDI-12 Transparent Mode ....................................... 241
FIGURE 65: PT100 BrHalf4W() Four-Wire Half-Bridge Schematic ......... 262
FIGURE 66: PT100 BrHalf3W() Three-Wire Half-Bridge Schematic ....... 266
FIGURE 67: PT100 BrFull() Four-Wire Full-Bridge Schematic ................ 270
FIGURE 68: HyperTerminal New Connection Description ....................... 292
FIGURE 69: HyperTerminal Connect-To Settings ..................................... 293
FIGURE 70: HyperTerminal COM Port Settings Tab: Click File |
Properties | Settings | ASCII Setup... and set as shown. ....................... 293
FIGURE 71: HyperTerminal ASCII Setup ................................................. 294
FIGURE 72: HyperTerminal Send-Text File Example ............................... 294
FIGURE 73: HyperTerminal Text-Capture File Example .......................... 295
FIGURE 74: Ac Power Noise Rejection Techniques .................................. 317
FIGURE 75: Input voltage rise and transient decay .................................... 319
FIGURE 76: Settling Time for Pressure Transducer .................................. 321
FIGURE 77: Example voltage measurement accuracy band, including
the effects of percent of reading and offset, for a differential
measurement with input reversal at a temperature between 0 to
40 °C. ................................................................................................... 329
FIGURE 78: PGIA with Input Signal Decomposition ................................ 348
FIGURE 79: Simplified voltage measurement sequence. ........................... 348
FIGURE 80: Programmable Gain Input Amplifier (PGIA): H to V+, L
to V–, VH to V+, VL to V– correspond to text. ................................... 349
FIGURE 81: Ac Power Noise Rejection Techniques .................................. 354
FIGURE 82: Input voltage rise and transient decay .................................... 357
FIGURE 83: Settling Time for Pressure Transducer .................................. 359
FIGURE 84: Example voltage measurement accuracy band, including
the effects of percent of reading and offset, for a differential
measurement with input reversal at a temperature between 0 to
40 °C. ................................................................................................... 368
FIGURE 85: Pulse Sensor Output Signal Types ......................................... 370
FIGURE 86: Switch Closure Pulse Sensor ................................................. 370
FIGURE 87: Terminals Configurable for Pulse Input ................................ 371
FIGURE 88: Amplitude reduction of pulse count waveform (before and
after 1 µs µs time-constant filter) ......................................................... 381