Korg Kronos - Effect Presets

Effects selection and routing Using effects in Combinations and Songs
205
TrackMixerpage,sothatthesignalssenttotheREC
bus(es)canberecordedtothedisk.
Insert effects
Continuingfromtheabove:
1. GototheCombinationP8:InsertEffect–InsertFX
page.
2. Choosetheeffecttypethatyouwanttousefor
eachinserteffectIFX1–12.
Pressthepopupbutton,andchooseaneffectfrom
theninecategories.
3. PresstheOn/Offbuttontoturnontheinsert
effect.
Eachtimeyoupressthebutton,theinse
rteffectwill
beswitchedon/off.WhenOff,theresultwillbethe
sameaswhen000:NoEffectisselected.Theinput
soundwillbeoutputwithoutchange.
4. MakeChainsettings.
IftheChaincheckboxischecked,theinserteffect
willbeconnectedinseries.
MakesettingsforPan(CC#8),“BusSel.(Bus
Select),”“Send1,”“Send2,”RECBusand“Ctrl
Bus”forthesoundafterithaspassedthroughthe
inserteffects.
Ifyou’vespecifiedachain,thesettingsthatfollow
thelastIFXinthechainwillbevalid(exceptfor
“CtrlBus”).
Pan:Setsthepan.
BusSel.(B
usSelect):Specifiestheoutput
destination.NormallyyouwillsetthistoL/R.Ifyou
wishtosendthesoundthathaspassedthroughthe
inserteffectstoAUDIOOUTPUT(INDIVIDUAL)
1–4,select1–4,1/2,or3/4.
Send1,Send2:Setsthesendlevelstothemaster
eff
ects.Forthisexample,setthisto127.
CtrlBus:TheFXControlBusesletsyoucreate
effects“sidechains.”Sidechainsletyoucontrolan
effectwithoneaudiosignal(thesidechain),while
theeffectprocessesacompletelydifferentaudio
signal.Thisisconvenientforusewithvocoders,
compressorsandlimiters,gates,et
c.Formore
information,see“FXControlBuses”onpage 860of
theParameterGuide.
RECBus:TheIFXoutputwillgototheRECbus.In
theP0–AudioInput/Samplingpage,youcansetthe
SamplingSetupSourceBustoaRECbus,and
samplethesignalthatissenttotheRECbus.Use
thisifyo
uwanttosampleonlythesoundofan
audioinputsourcebeingprocessedbyaninsert
effect(andnotsamplethesoundoftheoscillator
output).Youcanalsousethisifyouwanttosample
onlyaspecifictimbre.Alternatively,thedi
rect
so
undfromtheaudioinputscanbemixedwiththe
soundprocessedbyaninserteffect,senttoaREC
bus,andsampled.
Note:InSequencermode,youcanalsochooseaREC
busastheRECSourceforeachtrackintheP0–
AudioTrackMixerpage,sothatthesignalssentto
theRECbu
s(es)canberecordedtothedisk.
YoucanuseMIDItocontroldynamicmodulation
(Dmod)foreacheffect,thepost‐IFXpan(CC#8),
andSend1andSend2.
Anasterisk“*”isshownattherightofCh01–Ch16
forthechannelnumberoftracksroutedtoIF
X.If
you’veroutedmultipletracksthathavediffering
MIDIchannelsettings,thisspecifiesthechannelon
whichtheywillbecontrolled.
5. GototheIFX1–12pagestoedittheindividual
effectparameters.
Formoredetails,seestep6under“Usingeffectsin
Programs,”beginningonpage 202.
Master effects and Total effects
Thesesettingscanbemadeinthesamewayasin
“UsingeffectsinPrograms”(p.203).
YoucancontroltheseeffectsviaMIDIonthe“Ctrl
Ch.”ThespecifiedMIDIchannelwillcontrol
dynamicmodulation(Dmod)fortheMasterand
TotalEffects.