PREVOST LE MIRAGE XLII BUS SHELLS User Manual

ii
62--11052
PARAGRAPH NUMBER
Page
3.8 COMPRESSOR RUNNING GEAR REASSEMBLY 3-6........................................
3.8.1 Seal End Main Bearings 3-6............................................................
3.8.2 Pistons, Rods, and Rings 3-6...........................................................
3.8.3 Crankshaft and Seal End Thrust Washer 3-7.............................................
3.8.4 Bottom Plate, Strainer, and Connecting Rod Caps 3-7.....................................
3.9 SUCTION STRAINER 3-7.................................................................
3.10 ADDING OIL 3-7.........................................................................
3.11 INSTALLING COMPRESSOR 3-7..........................................................
LIST OF ILLUSTRATIONS
FIGURE NUMBER Page
Figure 1-1. Model 05G Compressor 1-2............................................................
Figure 1-2. Suction & Discharge Valve 1-3..........................................................
Figure 1-3. Oil Pump 1-3..........................................................................
Figure 1-4. Shaft Seal Reservoir 1-3................................................................
Figure 1-5. Compressor Unloader 1-4..............................................................
Figure 1-6. Electric--Operated Unloader--Unloaded Operation 1-4.......................................
Figure 1-7. Electric--Operated Unloader--Loaded Operation 1-5........................................
Figure 1-8. Pressure-Operated Unloader Loaded Operation 1-5........................................
Figure 1-9. Pressure-Operated Unloader -Unloaded Operation 1-5.....................................
Figure 2-1. Removal of Piston Plug 2-1.............................................................
Figure 2-2. Oil Level in Sight Glass 2-2.............................................................
Figure 3-1. Shaft Seal Reservoir 3-1................................................................
Figure 3-2. Cylinder Head & Valve Plate 3-2........................................................
Figure 3-3. Installing Suction Valves 3-2............................................................
Figure 3-4. Checking Suction Valve 3-2.............................................................
Figure 3-5. Oil Pump and Bearing Head Assembly 3-3................................................
Figure 3-6. Oil Pump 3-3..........................................................................
Figure 3-7. Shaft Seal 3-3.........................................................................
Figure 3-8. Shaft Seal Removal 3-4................................................................
Figure 3-9. TOP Orientation 3-4...................................................................
Figure 3-10. Bottom Plate Removal 3-5.............................................................
Figure 3-11. Bottom Plate and Oil Strainer Removed 3-5..............................................
Figure 3-12. Piston Rings Removed 3-5.............................................................
Figure 3-13. Connecting Rod, Piston, and Pin 3-5....................................................
Figure 3-14. Seal End Main Bearings 3-6...........................................................
Figure 3-15. Piston 3-6...........................................................................
Figure 3-16. Correct Piston in CylinderOrientation 3-6................................................
Figure 3-17. Installing Piston Rod Assemblies and Seal End Thrust Washer 3-6..........................
Figure 3-18. Piston Rings 3-7......................................................................
Figure 3-19. Installing Pistons 3-7..................................................................
Figure 3-20. Installing Suction Strainer 3-7..........................................................
Figure 3-21. Piston Dimension (Wear Limits) 3-9.....................................................
LIST OF TABLES
TABLE NUMBER Page
Table 1-1. Compressor Reference Data 1-1..........................................................
Table 1-2. Oils 1-1................................................................................
Table 3-1. Torque Values 3-8.......................................................................
Table 3-2. Wear Limits 3-9.........................................................................

PREVOST LE MIRAGE XLII BUS SHELLS Specifications

General

Brand	PREVOST
Model	LE MIRAGE XLII BUS SHELLS
Category	Buses
Language	English