To Next Page

To Previous Page

8-8 Rapidlab 1200 Operator’s Guide: System Configuration

02087462 Rev. V

Glu

10–998 mg/dL

Lac

0.00–30.00 mmol/L

tHb

†

2.0–25.0 g/dL

†

0.0 ± 200.0 (QC ranges) %

†

0.0 ± 100.0 (patient ranges) %

FCOHb

†

0.0 ± 200.0 %

FMetHb

†

0.0 ± 200.0 %

FHHb

†

0.0 ± 200.0 %

* Indicates parameters available only on Rapidlab 1260 and Rapidlab 1265 systems.

† Indicates parameters available only on Rapidlab 1245 and Rapidlab 1265 systems.

Parameter Default Range Default Units

Default Chapter3
- Organization3
- Conventions4
  - Table of Contents7
1 System Overview and Intended Use21
- Intended Use21
- Features21
- Hardware Overview22
- Software Overview39
  - Rapidlab ® User Interface39
    - Viewing the Banner Information40
    - Viewing the Display Area41
  - Rapidlab Main System Screens41
- Rapidlab 1200 Systems Sample Path45
  - System Sample Path45
  - CO-Ox Sample Path46
- Rapidlab 1200 Systems Technology47
Parameters72
- Bicarbonate Ion74
- Base Excess74
- Total Carbon Dioxide75
- Hematocrit75
- Patient Temperature Correction76
- Hemoglobin Oxygen Saturation76
- Calcium Adjustment for Ph79
- Anion Gap79
- Gas Exchange Indices80
- Alveolar-Arterial Oxygen Tension Difference80
- Arterial-Alveolar Oxygen Tension Ratio80
- Respiratory Index81
  - Arterial-Venous Oxygen Content Difference82
    - Physiologic Shunt83
  - References85
2 Operating the System89
- Using Basic System Functions89
- Collecting Patient Samples95
- Analyzing Samples99
- Entering Patient Sample Data110
- Using Patient Results115
- Printing Reports119
  - Procedural Notes for Printing Reports119
    - Printing Reports on the Internal Printer119
    - Printing Reports on the External Printer120
  - Using Available Reports120
- Performing a Correlation Study122
- Combining Results for an A-V Study Report123
  - Before You Begin124
  - Setting up the Data124
    - Printing the Arterial-Venous Study Report125
3 Calibration127
- Understanding Automatic Calibrations127
  - Troubleshooting Failed Calibrations129
  - Generating Calibration Reports129
- Performing Manual Calibrations130
  - Recalling Calibration Results130
4 Quality Control131
- Performing QC Sample Analysis131
- Accessing QC Results135
- Restoring Parameters142
5 Maintenance143
- Preparing for Maintenance Procedures143
- Performing Daily Maintenance144
- Performing Twice Weekly Maintenance145
  - Analyzing High G/L145
- Performing Weekly Maintenance146
- Performing Every 60 Days Maintenance151
  - Replacing the CO-Ox Sample Chamber151
  - Checking the Air Filters151
- Performing Quarterly Maintenance152
  - Replacing the Pinch Valve Tubing152
    - Testing for Leaks153
- Yearly Maintenance153
- Cleaning Procedures163
Maintaining the Sensors171
- Replacing the Sensors171
- Performing Reference Sensor Maintenance176
- Performing Measurement Sensor Maintenance182
Replacing System Components184
- Replacing the Printer Paper184
- Replacing the Sample Port184
- Replacing the CO-Ox Lamp185
- Replacing the CO-Ox Roller Cage187
- Replacing the System Fuses189
Relocating the System191
Shipping or Storing the System192
- Cleaning the Sample Path192
- Removing the Cartridges192
- Cleaning and Drying the Tubing193
- Scheduling Maintenance Activities203
6 Troubleshooting207
- Troubleshooting Failed or Missed QC Analysis207
- Troubleshooting Failed Calibrations210
  - Troubleshooting Checklist for Failed Calibration210
  - Using the Calibration Report to Identify Problems211
- Troubleshooting Patient Results212
- Troubleshooting Unavailable Buttons213
- Troubleshooting Measurement Module Lights214
- Troubleshooting Barcode Problems214
  - Barcode Quality214
  - Resetting the Barcode Scanner215
- Troubleshooting Internal Printer Problems217
- Troubleshooting Touchscreen Problems217
- Solving Communication Problems218
- Removing Obstructions from the CO-Ox Sample Path237
- Using Diagnostics239
D Codes253
- D2 Codes254
- D3 Codes257
- D4 Codes259
- D5 Codes260
  - D5 no Endpoint: Ca260
  - D5 no Endpoint: Glu Lac261
- D6 Codes262
- Viewing System Messages280
7 File Management291
- File Names and Formats291
- Copying Data Files292
  - Copying Patient, QC, or Calibration Data Files293
  - Copying Diagnostic Data293
- Viewing the Sample Totals294
8 System Configuration295
- Using the Setup Menu295
- Setting up QC296
- Setting up Sample Information301
- Setting up Parameters307
- Setting up System Options313
- Setting up Printer and Devices Options316
- Setting up Secured Options329
Appendix A: Safety Instructions341
- Protecting Yourself from Biohazards341
  - References342
- Protecting Yourself from Barcode Scanner Lasers343
- Protecting Yourself from Electrical Hazards343
Appendix B: Service, Ordering, and Warranty345
- Authorized Representative345
- Limited Instrument Warranty and Service Delivery Policy345
- Contacts353
  - Authorized Representative353
  - Addresses353
Appendix C: System Fluids355
- Recommended Fill Volumes355
- Rapidlab 1200 Cartridges356
Appendix D: Supplies357
Appendix E: System Specifications361
- Viewing Parameter Measurements361
  - Understanding System Limitations365
- Interference Testing366
- Performance Characteristics371
- Reference Methods432
- Calibrator Traceability433
- References433
Appendix F: Symbols435
Appendix G: Glossary437
Appendix H: Rapidlab 1200 System Maintenance Checklist439
- Daily Maintenance439
- Twice Weekly Maintenance439
- Weekly Maintenance439
- Every 60 Days Maintenance440
- Quarterly Maintenance440
- Yearly Maintenance440
- As Required Maintenance440

Brand	Siemens
Model	Rapidlab 1200
Category	Medical Equipment
Language	English

Siemens Rapidlab 1200 User Manual

Table of Contents

Questions and Answers:

Siemens Rapidlab 1200 Specifications

Related product manuals