5.12.3.3 I/O 21
Error Code Error Type Error Text / Remarks
3001 INFO
I/O 21, Rack ‘Int’: Reconfiguration required.
3002 INFO
I/O 21, The Rack
‘Ext 1’ was reconfigured. Please make sure the Core is rebooted in order to achieve
system consistency.
3003 WARNING
I/O 21, Slot change: Card from Slot ‘2’ of the rack ‘Internal’ removed.
3004 INFO
I/O 21, Slot change: Same Card in Slot ‘2’ of the rack ‘External 1’ re-installed.
3005 INFO I/O 21, Slot failure: The Card in Slot 13 must be a GPIO Card.
3006 INFO
I/O 21, Slot change: Card to Slot ‘2’ added. Please reconfigure the rack ‘Internal’ and reboot the Core in
order to achieve system consistency.
3007 WARNING
I/O 21, Slot failure: Unknown Card found. Card in Slot ‘3’ of the rack ‘D21m Rack 1’ not supported.
3008 WARNING
I/O 21, Secondary power failure: Digital Power. (Rack
‘External 2’)
* 3009 WARNING I/O 21, Secondary power failure: Analog Power. (Rack ‘External 2’)
3010 WARNING
I/O 21, Primary Power Supply 1 fail. (Rack ‘External 1’)
3011 WARNING
I/O 21, Primary Power Supply 2 fail. (Rack ‘Internal’)
3012 WARNING
I/O 21, Failure of fan. (Rack ‘Internal’).
3013 WARNING I/O 21, Couldn’t open the COM port.
3014 ERROR
I/O 21, Missing D21m rack ‘External 1’.
3015 ERROR
I/O 21, Fan unit disconnected. (Rack ‘Internal’).
3016 WARNING
I/O 21, Communication to rack ‘Internal’ lost.
3018 INFO I/O 21, Invalid module on merger port 13
3021 INFO
I/O 21, The card in slot
‘2’ of the rack ‘External 3’ is not allowed in this slot.
3022 INFO
I/O 21, Additional HD Link to a DSP card required. Rack
‘Int’ provides ‘128’ Inputs, but only ‘96’ channels
are connected to the Core. ‘32’ inputs not available.
3023 INFO
I/O 21, Additional HD Link to a DSP card required. Rack ‘Int’ provides
‘128’ outputs, but only ‘96’ channels
are connected to the Core. ‘32’ outputs not available.
3024 INFO
I/O 21, MADI card in slot ‘3’ of the rack ‘Int’ switched to redundant interface. AUX interface is active.
3025 WARNING
I/O 21, MADI card in slot 3 of rack ‘Int’: Neither MAIN nor AUX interface is active.
3026 INFO
I/O 21, Not enough MADI channels from StageBox ‘StageBox1’ to Rack ‘Int’. Provides ‘80’ inputs, but
only ‘64’ channels are available. ‘16’ inputs not available.
3027 INFO
I/O 21, Not enough MADI channels from StageBox ‘StageBox1’ to Rack ‘Int’. Provides ‘80’ outputs, but
only ‘64’ channels are available. ‘16’ outputs not available.
3030 WARNING
I/O 21, HD Card unlock. Missing HD Link input signal. (Rack ‘External 2’)
3031 INFO
I/O 21, HD Card lock. HD Link input signal available. (Rack ‘External 2’)
3033 WARNING
I/O 21, Configuration mismatch: Card from Slot 2 of the rack ‘Internal‘ and the D21m.xml configuration
doesn’t match. XML configuration ignored!
3034 WARNING
I/O 21, Configuration mismatch: Card from Slot 2 of the rack ‘StageBox1‘ and the D21m.xml configuration
doesn’t match. Hardware configuration ignored!
3102 WARNING
GPIO, The GPIO function on pin
‘3’ doesn‘t work properly! Please check the selected arguments.
3103 WARNING
GPIO, Missing GPIO Card(s). ‘32’ Pins configured, ‘16’ Pins found.
3104 WARNING
GPIO, Snapshot File ‘myGlobalSnap’ not found. The GPIO function ‘3’ doesn‘t work properly!
* OnAir 3000 only
To Next Page
Loading...
Need help?
General
