EasyManuals Logo

Keysight E4980A User Manual

Keysight E4980A
519 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #260 background imageLoading...
Page #260 background image
260 Keysight E4980A/AL Precision LCR Meter
Overview of Remote Control
Data Transfer
8-
Data Transfer
This section describes data transfer.
Data Format
The E4980A/AL offers two data formats for GPIB data transfer to the controller,
ASCII and BINARY. Data transfer rates vary depending on the data format
used.
ASCII Format
The ASCII data format is the default output format. When the :FORM:DATA
ASC command is executed, the E4980A/AL transfers data in the ASCII format.
The ASCII format of the E4980A/AL has two modes: the six-significant-digit
mode and the ten-significant-digit mode. The six-significant-digit mode is the
default, though the format can be switched to the ten-significant-digit mode
by using the :FORM:ASC:LONG ON command. The ASCII data output format
on the MEAS DISPLAY, BIN No., or BIN COUNT page is described below.
Figure 8-21 ASCII Format 1
The <DATA A>, <DATA B>, <STATUS>, and <BIN No.> formats are as follows.
<DATA A> and <DATA B> format:
㪼㪋㪐㪏㪇㪸㫌㪼㪈㪇㪊㪇
(14/#5%.10)1((
(14/#5%.10)10
㪪㪥㪅㪥㪥㪥㪥㪥㪥㪥㪥㪥㪜㪪㪥㪥 㪪㪥㪅㪥㪥㪥㪥㪥㪥㪥㪥㪥㪜㪪㪥㪥
㪪㪥
㪪㪥㪅㪥㪥㪥㪥㪥㪜㪪㪥㪥 㪪㪥㪅㪥㪥㪥㪥㪥㪜㪪㪥㪥
㪪㪥
㪪㪥㩷㫆㫉㩷㪪㪥㪥
㪚㪦㪤㪧㪑㩷㪦㪥
㪚㪦㪤㪧㪑㩷㪦㪝㪝
㪪㪥㩷㫆㫉㩷㪪㪥㪥
㪚㪦㪤㪧㪑㩷㪦㪥
㪚㪦㪤㪧㪑㩷㪦㪝㪝
㪥㪣㪵㪜㪥㪛
㪥㪣㪵㪜㪥㪛
&#6## &#6#$ 56#675 $+00Q
&#6## &#6#$ 56#675 $+00Q
㪼㪋㪐㪏㪇㪸㫌㪼㪈㪇㪊㪇
(14/#5%.10)1((
(14/#5%.10)10
㪪㪥㪅㪥㪥㪥㪥㪥㪥㪥㪥㪥㪜㪪㪥㪥 㪪㪥㪅㪥㪥㪥㪥㪥㪥㪥㪥㪥㪜㪪㪥㪥
㪪㪥
㪪㪥㪅㪥㪥㪥㪥㪥㪜㪪㪥㪥 㪪㪥㪅㪥㪥㪥㪥㪥㪜㪪㪥㪥
㪪㪥
㪪㪥㩷㫆㫉㩷㪪㪥㪥
㪚㪦㪤㪧㪑㩷㪦㪥
㪚㪦㪤㪧㪑㩷㪦㪝㪝
㪪㪥㩷㫆㫉㩷㪪㪥㪥
㪚㪦㪤㪧㪑㩷㪦㪥
㪚㪦㪤㪧㪑㩷㪦㪝㪝
㪥㪣㪵㪜㪥㪛
㪥㪣㪵㪜㪥㪛
&#6## &#6#$ 56#675 $+00Q
&#6## &#6#$ 56#675 $+00Q

Table of Contents

Other manuals for Keysight E4980A

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Keysight E4980A and is the answer not in the manual?

Keysight E4980A Specifications

General IconGeneral
Frequency Range20 Hz to 2 MHz
Basic Accuracy0.05%
DC Bias Voltage0 V to ±40 V
Measurement FunctionsL, C, R, Z, D, Q
DC Bias Current0 A to 20 mA (using external DC bias source)
DisplayLCD
InterfaceLAN, USB, GPIB
Dimensions426 mm (W) x 177 mm (H)
Weight13.5 kg

Related product manuals