I-2 Index
Error Messages
dispenser motor references not found ...................... 4-3
interlock active ......................................................... 2-15
scale ......................................................................... 7-11
F
Facility Requirements ..................................................... 9-2
Fiducials ............................................................... 4-27, 4-30
Fids-on-the-Fly ........................................................... 1-7
Fluid
supported dispensing fluids ....................................... 1-2
Fluid Manager ............................................................... 4-31
Fluidmove
beacon configuration ............................................... 5-34
creating a pattern .................................................... 4-43
creating a program ................................. 4-27–4-46, 4-28
current air flow toolbar ............................................ 5-27
current pressure window ........................................... 4-9
dispensing elements ................................................ 4-40
dual conveyor programming ........................... 4-41–4-42
electronic pressure control utility .............................. 4-8
fluid files ................................................................... 4-30
loading a part ........................................................... 4-28
placing a pattern ...................................................... 4-44
program commands ................................................. 4-38
running a program in dry mode ............................... 4-46
setting the heater temperature ............................... 4-35
starting .......................................................................
4-3
teaching workpiece origin ........................................ 4-29
workpiece alignment................................................ 4-27
Front Panel.................................................................... 1-18
Fuse Replacement
board-mounted ........................................................ 8-11
panel-mounted ........................................................ 8-14
replaceable fuse list ................................................. 8-11
G
Gauges
digital
initialization ........................................................ 5-17
H
Heater ........................................................................... 4-34
setup ........................................................................ 4-34
substrate
setting temperature ............................................ 4-35
Heaters
calibrating ................................................................ 5-21
contact ....................................................................... 1-7
impingement .............................................................. 1-7
adjusting manual airflow..................................... 5-29
controlled process heat ...................................... 5-25
cooldown ............................................................ 5-28
needle ................................................................
........ 1-8
setting the temperature...................................... 4-37
troubleshooting .................................................. 7-12
substrate
troubleshooting .................................................... 7-8
Height Sensor .................................................................. 1-8
laser
specifications ....................................................... 2-13
troubleshooting ..................................................... 7-6
mechanical/tactile
probe adjustment ................................................ 5-13
probe replacement .............................................. 8-10
troubleshooting ..................................................... 7-6
I
Impingement Flowmeters
functional testing ...................................................... 5-29
Installation
anchoring the dispensing system ............................. 3-12
computer .................................................................. 3-10
connecting the power and air supply ....................... 3-13
dispensing valve ......................................................... 4-4
leveler adjustment ...................................................... 3-3
light beacon ................................................................ 3-9
scale ............................................................................ 3-4
service station ............................................................ 3-8
uncrating and placing the dispensing system ............. 3-2
unpacking dispensing chamber .................................. 3-4
Interlock ................................................................. 1-8, 2-15
recovery .................................................................... 2-15
verifying functionality ................................................. 6-8
J
Jog Controls
conveyor ................................................................... 4-14
dispenser .................................................................. 4-12
dual conveyor systems ............................................. 4-15
keyboard commands ................................................ 4-17
Jog Window ................................................................... 4-11
L
Laser Height Sensor
specifications ............................................................ 2-13
troubleshooting .......................................................... 7-6
Laser Radiation Safety ..................................................... 2-3
Levelers
adjusting ..................................................................... 3-3
Leveling
dispensing system ...................................................... 3-6
Lift Table
speed adjustment ..................................................... 5-31
Light Beacon ........................................................... 1-8, 2-18
color indications ....................................................... 2-18
configuration ............................................................ 5-34
installation .................................................................. 3-9
Line Parameters ............................................................ 4-33
Linear Encoders
adjusting the X-axis linear encoder
.......................... 6-19
adjusting the Y-axis linear encoder gap .................... 6-21
adjusting the Z-axis linear encoder gap .................... 6-23
Loading a Part ................................................................ 4-28
Lockout/Tagout ............................................................. 2-16
LOTO ..................................................... See Lockout/Tagout
To Next Page
Loading...
Need help?
General